Yamaha Yamaha Mixing Consol, M2500 owner manual Specifications, General specifications

Specifications

General specifications

0 dB is referenced to 0.775 Vrms.

Total Harmonic Distortion	Less than 0.1% (THD+N)
(Master output)	20 Hz–20 kHz @ +14 dB 600 Ω
Frequency Response	0+1, –3 dB
(Master Output)	20 Hz–20 kHz @ +4 dB 600 Ω
	Gain control at minimum level
Hum & Noise (20 Hz–20 kHz)*1	–128 dB Equivalent Input Noise.
Rs= 150 Ω	–99 dB Residual Output Noise.

(STEREO OUT, MONO/C OUT,

GROUP/AUX OUT, AUX OUT, AUX/GROUP OUT)

Input Gain= Max.

Input Pad= OFF

Input sensitivity= –60 dB

–64 dB(68 dB S/N) STEREO OUT Master Level control and one Ch fader at nominal level.

–80 dB(84 dB S/N) STEREO OUT, MONO/C OUT Master fader at nominal level and all Ch assign SW’s off and all GROUP to ST SW’s off.

–81 dB(85 dB S/N) GROUP1/AUX7–GROUP8/AUX14 OUT Master Level control at nominal level and all Ch assign SW’s off.

GROUP/AUX FLIP SW off.

–75 dB(79 dB S/N) AUX1–6, AUX7/GROUP1–AUX14/GROUP8 OUT Master Level control at nominal level and all Ch send controls at minimum. GROUP/AUX FLIP SW off.

–90 dB(94 dB S/N) MATRIX OUT Master level control at nomi- nal level and all Matrix Mix controls at mini- mum level.

Crosstalk	–70 dB @	1 kHz	adjacent inputs.
	–70 dB @	1 kH	input to output. (CH INPUT)
	–50 dB @	1 kHz	input to output. (ST CH INPUT)
Maximum Voltage Gain
GROUP/AUX FLIP SW= off
	60 dB	CH INPUT to CH INSERT OUT
	84 dB	CH INPUT to GROUP1/AUX7–GROUP8/
		AUX14 OUT
	80 dB	CH INPUT to AUX1, 2 OUT(Pre Fader)
	90 dB	CH INPUT to AUX3–6, AUX7/GROUP1–
		AUX14/GROUP8 OUT(Post Fader)
	84 dB	CH INPUT to STEREO OUT(CH to ST)
	70 dB	CH INPUT to MONITOR OUT(PFL)
CH INPUT PAD SW		26 dB
CH INPUT GAIN control		44 dB	variable
ST CH 1A, 2–4 INPUT GAIN control
		40 dB	variable
ST CH 1B INPUT GAIN control
		30 dB	variable
CH INPUT High Pass Filter		18 dB/octave
		roll-off below 80 Hz at –3 dB point.
CH INPUT Equalization
+15, –15 dB maximum
	HIGH	10 kHz (shelving)
	HIGH-MID	400– 8 kHz (peaking)
	LOW-MID	80–1.6 kHz (peaking)
	LOW	100 Hz (shelving)

ST CH INPUT Equalization
+15, –15 dB maximum
		HIGH	10 kHz (shelving)
		LOW	100 Hz (shelving)
Phantom Power		+48 VDC is applied to balanced inputs (via
		6.8 kΩ current-limiting/isolation resistors) for
		powering condenser microphones; may be
		turned ON or OFF via rear-panel phantom
		Master switch.
		When Master is ON, individual channels
		may be turned ON or OFF via +48V
		switches (with red LED) on each input chan-
		nel.
CH LED Indicators
	PEAK	LED(red) built into each CH INPUT turns on
		when pre-Fader level reaches +17 dB.
	NOM	LED(yellow) built into each CH INPUT turns
		on when pre-Fader level reaches 0 dB.
	SIGNAL	LED(green) built into each CH INPUT turns
		on when pre-Fader level reaches –13 dB.
ST CH LED Indicators
	PEAK	LED(red) built into each ST CH INPUT turns
		on when pre-Fader [L+R] level reaches
		+17 dB.
	NOM	LED(yellow) built into each ST CH INPUT
		turns on when pre-Fader [L+R] level
		reaches 0 dB.
	SIGNAL	LED(green) built into each ST CH INPUT
		turns on when pre-Fader [L+R] level
		reaches –13 dB.
Oscillator/Noise		Switchable sine wave @ 100 Hz, 1 kHz or
		10 kHz, or pink noise.
Scene Memory		Direct Scene Memory recall switches (1–8)
		Switchable Scene Memory recall (1–128)
VU Meters		11 illuminated meters
		(0VU= +4 dB output @ 600Ω load)
	#1 ; GROUP1/AUX7•AUX1•AUX7/GROUP1•MATRIX1
	#2 ; GROUP2/AUX8•AUX2•AUX8/GROUP2•MATRIX2
	#3 ; GROUP3/AUX9•AUX3•AUX9/GROUP3•MATRIX3
	#4 ; GROUP4/AUX10•AUX4•AUX10/GROUP4•MATRIX4
	#5 ; GROUP5/AUX11•AUX5•AUX11/GROUP5•MATRIX5
	#6 ; GROUP6/AUX12•AUX6•AUX12/GROUP6•MATRIX6
	#7 ; GROUP7/AUX13•NONE•AUX13/GROUP7•MATRIX7
	#8 ; GROUP8/AUX14•NONE•AUX14/GROUP8•MATRIX8
	#9 ; STEREO L•PFL/AFL L
	#10 ; MONO/C
	#11 ; STEREO R•PFL/AFL R
VU Meter Peak Indicators		LED(red) built into each VU meter turns on
		when output signal is above the level 3 dB
		lower than clipping level.
Dimension	Heigt	265 mm
	Depth	875 mm (except rear connectors)
	Width	2385 mm(56C), 2142 mm(48C),
		1899 mm(40C), 1642 mm(32),
		1400 mm(24)
Weight		102kg(56C), 93kg(48C), 84kg(40C),
		71kg(32), 62kg(24)

*1 Hum & Noise are measured with a 6 dB/octave filter @ 12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation.

For European Model

Purchaser/User information specified in EN55103-1 and EN55103-2. Conformed Enviroment: E1, E2, E3 and E4.

40 M2500—Owner’s Manual