Initial settings

If an error message is displayed

If an error message is displayed on the TV screen, see “Error messages” below to determine the cause and resolve the problem. Follow the instructions below to begin measurement again.

[ERROR E-1]

Press the ENTER key to run the AUTO SETUP procedure again. Or press the X key to continue the measurement.

[ERROR E-7]

Press the key to turn this unit to the standby mode, then run AUTO SETUP procedure again after turning this unit on.

[ERROR E-9]

1Be sure that a wireless connection between the subwoofer and center unit has been established (☞p. 20).

2Press the RETURN key.

The “IntelliBeam” menu is displayed.

3Select “BEAM+SOUND OPTIMIZE”, “BEAM OPTIMIZE ONLY”, or “SOUND OPTIMIZE ONLY” and press the X key.1)

4Follow steps 4, 5, and 6 to measure again (☞p. 25).

[ERROR E-2] through [ERROR E-6]

1Press the RETURN key.

The “IntelliBeam” menu is displayed.

2Select “BEAM+SOUND OPTIMIZE”, “BEAM OPTIMIZE ONLY”, or “SOUND OPTIMIZE ONLY” and press the X key.1)

3Follow steps 4, 5, and 6 to measure again (☞p. 25).

Error messages

ERROR E-1: Please test in quieter environment.

Cause

Remedy

 

 

There is too much noise in your

Make sure that your listening

listening room.

room is as quiet as possible. You

 

may want to choose certain hours

 

during the day when there is not

 

much noise coming from outside.

 

 

ERROR E-4: Please check MIC position. MIC should be set in front of Sound Projector. Please re-try.

Cause

Remedy

 

 

The IntelliBeam microphone is

Position the IntelliBeam

not placed in front of this unit.

microphone in front of this unit

 

and begin measurement again.

 

 

ERROR E-5: Please check MIC position. MIC should be set above 1.8m/6.0ft and re-try.

Cause

Remedy

 

 

The IntelliBeam microphone is

Position the IntelliBeam

not placed in the right distance

microphone at a distance of more

from this unit.

than 1.8 m (6.0 ft) from this unit

 

and begin measurement again.

 

 

ERROR E-6: Volume level is lower than expected. Please check MIC position/connection and re-try.

Cause

Remedy

 

 

The IntelliBeam microphone

Position the IntelliBeam

cannot collect the sound

microphone properly, check the

produced by this unit.

connection, and then begin

 

measurement again.

 

 

ERROR E-7: Unexpected error happened. Please turn off and re-try.

Cause

Remedy

 

 

An internal system error

Press the key to turn this unit

occurred.

to the standby mode, then run

 

AUTO SETUP procedure again

 

after turning this unit on.

 

 

ERROR E-9: Check the connection with subwoofer.

Cause

Remedy

 

 

The subwoofer is not connected

Be sure that a wireless

wirelessly.

connection between the

 

subwoofer and center unit has

 

been established (☞p. 20) and

 

measure again.

 

 

PREPARATION

PLAYBACK

SETTINGS

ERROR E-2: No MIC detected. Please check MIC connection and re-try.

Cause

Remedy

 

 

The IntelliBeam microphone is

Connect the IntelliBeam

disconnected.

microphone to the

 

INTELLIBEAM MIC jack on the

 

rear of this unit and begin

 

measurement again.

 

 

TROUBLESHOOTING

ERROR E-3: Unexpected control is detected. Please re-try.

Cause

Remedy

 

 

Some other operations were

Begin measurement again. Do

performed on this unit.

not perform any other operations

 

with this unit during

 

measurement.

 

 

APPENDIX

27 En