York DFAH, DFAA Duct Connectors, Installation Of Screw Attachment Duct Connector, UIM-B-1105

107272-UIM-B-1105

DUCT CONNECTORS

	18-3/4 (47.6 cm)	2-3/8				18-3/4 (47.6 cm)	2-3/8
		(6.0 cm)		SEE			(6.0 cm)	SEE
2-3/8	14 (35.6 cm)				2-3/8	14 (35.6 cm)
				CHART				CHART
(6.0 cm)					(6.0 cm)
	13	12				13	12
	(33.0 cm)					(33.0 cm)
		(30.5 cm)					(30.5 cm)
						11
	11		18-3/4				18-3/4
						(27.9 cm
	(27.9 cm						(47.6 cm)
		(47.6 cm)
			4-3/8				4-3/8
							(11.1 cm)
			(11.1 cm)
	DUCT CONNECTOR DIMENSIONS					DUCT CONNECTOR DIMENSIONS
	DUCT CONNECTOR	DUCT CONNECTOR				DUCT CONNECTOR	DUCT CONNECTOR
	PART NUMBER	DEPTH				PART NUMBER	DEPTH
	7990-6011	1” (2.5 cm)				7990-6211	1” (2.5 cm)
	7990-6021	2” (5.7 cm)				7990-6221	2” (5.7 cm)
	7990-6041	4-1/2” (11.4 cm				7990-6241	4-1/2” (11.4 cm
	7990-6061	6-1-2” (16.5 cm)				7990-6261	6-1-2” (16.5 cm)
	7990-6071	7-1/2” (19.0 cm)				7990-6271	7-1/2” (19.0 cm)
	7990-6081	8-1/2” (21.6 cm)				7990-6281	8-1/2” (21.6 cm)
	7990-6101	10-1/4” (26.0 cm)				7990-6301	10-1/4” (26.0 cm)
	7990-6121	12-1/4” (21.1 cm)				7990-6321	12-1/4” (21.1 cm)

FIGURE 7: Duct Connector Dimensions

			Rear Wall		Ceiling Cut-Out
	2-3/4 (7.0 cm)		of Enclosure		For Roof Jack
	Min.
					Floor Cut-Out
					For Duct
					Connector
23-1/4(59.1cm)	1/2(52.1cm) 9-7/8 (25.1cm				Furnace
					Outline
		15	(38.1cm)	15
	-			(38.1 cm)
	20				Optional Gas
					or Electric
					Entrance
	2-1/8 (5.4 cm)				Front Panel
1					of Furnace
	1-3/8	6-3/8			1-1/8
	(3.5 cm)	(16.2 cm)		3-1/4	(2.9 cm)
			9-3/4	(8.3 cm)
Future
		24.8 cm)			Floor
Refrigerant
				20
Line Entrance
				(50.8 cm)

FIGURE 8: Recommended Floor Cut-out

	Floor
Duct Connector	Floor
	Joist
Depth
Supply Duct

FIGURE 9: Duct Connector Depth

Locator Bracket

Nails, Flat Head Screws or Staples

Screws

Floor

Supply Duct

FIGURE 10: Duct Connector Screw Attachment

INSTALLATION OF SCREW ATTACHMENT DUCT CONNECTOR

1.Make floor cut out as shown in Figure 8.

2.Determine the depth of the floor cavity from the surface of the floor to the top of the supply air duct and select the appropriate duct connector from the chart.

3.Place locating bracket (supplied with the duct connector) to the back edge of the floor opening. See Figure 10.

4.Apply a water based duct sealant to the 1/2 in (1.3 cm) supply duct attachment flange of the duct connector.

5.Determine which of the four positions the duct connector best cen- ters over the supply duct and insert it through the floor cut-out.

6.When properly aligned with the supply duct, secure the duct con- nector to the floor with nails, flat head screws or staples.

7.Use screws as required to secure the duct connector to the supply duct.

8.Cut out the opening to the supply duct. If sealant was not used, the installer should tape the mating flanges to provide a good air seal.

NOTE: Duct sealant and tape must be classified as meeting HUD Stan- dard 3280.715, U.L. Standard 181A.

If tape is used to provide a better air seal, it should be a type approved by the applicable national or local codes.

8 Unitary Products Group