Manuals / Brands / Musical Instruments & Equipment / Guitar / Zoom / Musical Instruments & Equipment / Guitar

Zoom 7072 Getting Connected, 1.Make sure that the amplifier and the 707II are off, 6.Turn power on in the following order: 707II → amplifier

1 40

Download 40 pages, 907.06 Kb

Getting Connected

Guitar

Guitar amplifier

AC adapter

Preparations

CD player or similar

Headphones

1.Make sure that the amplifier and the 707II are off.

Turn the volume at the amplifier to minimum.

2.To power the unit from the AC adapter, insert the small plug of the adapter cable into the [DC 9V] jack on the 707II. Then plug the adapter into an outlet.

3.Connect the guitar to the [INPUT] jack of the 707II, using a mono cable.

4.Connect the [OUTPUT/PHONES] jack of the 707II to the guitar amplifier, using a mono cable.

You can also use a Y cable to supply the signal in stereo to two amplifiers.

5.To monitor the sound with headphones, plug the phones into the [OUTPUT/ PHONES] jack.

6.Turn power on in the following order: 707II → amplifier.

NOTE

If you turn the 707II on while the amplifier is already powered up, damage to the speaker may result. Always turn power to the amplifier on last.

7.Raise the volume setting of the instrument and amplifier, and adjust the [OUTPUT] knob on the rear panel of the 707II.

ZOOM 707II GUITAR 7

Contents

CONTENTS USAGE AND SAFETY PRECAUTIONS Introduction Controls and Functions Top Panel Rear Panel POWER Preparations Inserting Batteries and a SmartMedia card Getting Connected Quick Guide (Let's Play) 1In play mode, press one of the [W]/[Q] foot switches 2 To switch the effect module on or off, push the expression pedal Changing the sound of a patch 1While playing your instrument, operate the knobs on the panel WER A0 Storing an effect 1Press the [STORE/EXECUTE] key [DRIVE VARIATION] key [DRIVE] knob Parameter knob 3 Adjusts the reverb and echo level Listening to Patches (Play Mode Operation) Panel Display in Play Mode Selecting a Patch Using the Tuner Function 440HZ Using the Easy Edit Function Using the Sampler Function SAMPLE SP NO SPMODE N1 SP LVL Using the Rhythm Function POWER A0 8BEAT BPM120 LVL Rhythm pattern list Changing the Sound of a Patch (Edit Mode) Patch Configuration ZNR Basic Edit Mode Steps HALL PD TIME TONE MIX Storing and Swapping Patches STORE? E3 Other Functions Using the Hold Delay Function STOP ■If a numeric value is set as TIME parameter Effect sound Direct sound ■If TIME parameter is set to "Mn" and MODE parameter to "So Changing the Patch Call Method Using the Pedal to Control an Effect ●MOD ●GAIN ●REV ●VOL ●SAMPLER Adjusting the Expression Pedal Storing Rhythm Patterns and Samples as Part of a Patch 8.Press the [R/P] key 10.Switch the patch 11.To stop rhythm pattern playback, press the [R/P] key 12.Press the [PATCH SYNC] key so that the LED of the key is out Assigning a sample to a patch LOAD Utility mode functions Storing a single patch on a SmartMedia card 1.In play mode, select the patch from internal memory that you want to store 2.Activate utility mode and select "SAVE". Then press the [STORE/ EXECUTE] key 5.To carry out the operation, press the [STORE/EXECUTE] key once more Storing a group on a SmartMedia card 1.In utility mode, select "ALSAVE" and press the [STORE/EXECUTE] key 3.To carry out the operation, press the [STORE/EXECUTE] key once more Deleting a group from a 1.In utility mode, select "P DEL" and press the [STORE/EXECUTE] key 2.Use the TYPE [W]/[Q] keys to select the patch group (1 – 5) for deleting 3.Press the [STORE/EXECUTE] key 4.To carry out the operation, press the [STORE/EXECUTE] key once more All Initialize/Factory Recall Effect Types and Parameters BOOSTER Module ISOLATOR/COMP (Isolator/Compressor) Module DRIVE Module EQ (Equalizer) Module ZNR/D GATE (ZOOM Noise Reduction/D Gate) Module CABINET Module MODULATION Module TYPE 9 STEP 36ZOOM 707II GUITAR DLY/REV (Delay/Reverb) Module TOTAL Module Troubleshooting Specifications Patch List