Manuals / Zoom / Computer Equipment / Modem

Zoom X4 manual Macintosh TCP/IP Settings, For Mac OS 7.6.1 - 9.2.2 and Above but not OS

Models: X4

1 56

Download 56 pages 29.83 Kb

Page 48

Macintosh TCP/IP Settings

Then click the DNS configuration tab, enter the DNS server information, and click OK.

6	You will see the Network dialog box again. Click OK to
	enable your settings. If prompted to do so, insert your

Windows 95 CD-ROM and click OK.

Macintosh TCP/IP Settings

Depending on your Mac OS, the directions to configure your Macintosh’s network settings will differ. For OS X, follow the instructions on page 50. Otherwise, continue directly below.

For Mac OS 7.6.1 - 9.2.2 and Above but not OS X

1From the Apple menu, choose Control Panels and then TCP/IP to display the TCP/IP dialog box (you will use this dialog box in Step 6).

2On the main toolbar, from the File menu, choose Configurations.

48	X4 ADSL Modem User’s Manual

Image 48

Zoom X4 manual Macintosh TCP/IP Settings, For Mac OS 7.6.1 - 9.2.2 and Above but not OS

Contents

ADSL Modem U S E R ’ S M A N U A LCopyright 2002 All rights reserved Contents Installation Instructions 1.1 Important! Before you Begin1.2 Package Contents Install the software before connecting the hardware 1.3 Quick Start InstructionsYou Will Also Need To Connect via the Ethernet OptionRESET ETHERNET PHONE ADSL panelAll hardware connections originate from the modem’s back PWR ON OFFPage b Click the ADSL Modem Installation Wizard button To Connect via the USB OptionHardware Installation disclaimer box or a Digital Establishing Communication with theNote You may see a Found New Hardware box User Name=admin Password=zoomadsl Remember The User Name and Password are case- sensitivewith your X4. This page provides details about your Internet Using Phone Filters 1.4 If You Need Help Advanced Setup Options 2.1 How To Use the Advanced Options2.2 WAN Settings Chapter 2 Advanced Setup Options Permanent VC Virtual Circuit Settings Enabled?ATM Service Category Static IP AddressDefault Gateway EncapsulationBridge IGMP Internet Group Management Protocol2.3 LAN Settings DHCP Dynamic Host Configuration ProtocolIP Address Subnet MaskDHCP Server DHCP Address Pool2.4 NAT Firewall Session NameUser’s IP Action2.5 Virtual Server 3 Select the Port Type. For FTP, it is TCP, which is the default Note These TCP/IP instructions and screenshot are typical of a computer using Windows 2000 or XP if you are using Windows 98 or Me, yours may differ slightly. If you are using Windows 95, or are a Macintosh or Linux user, and need help with your TCP/IP settings, turn to the Appendix on page 46. Otherwise, continue to Step 2.6 DMZ Default gateway X4’s LAN IP address Chapter 2 Advanced Setup OptionsIP address 10.0.0.152.7 DNS User ConfigurationDNS Proxy Selection 2.8 ADSL Configuration Enabled by defaultDefault is Autosense - G.dmt first Wiring Selection2.9 Miscellaneous Advanced Setup page and LAN Settings accessWAN side HTTP server HTTP server portSystem Administration 3.1 Monitoring System Status3.2 Monitoring ADSL Status Chapter 3 System AdministrationHighlight Release in the pulldown menu, and then click Save Changes 3.3 Performing System Administration Tasks Change the Admin PasswordPerform a Diagnostic Test View System Log3.4 Resetting the Unit to Its Default Settings 3.5 Updating the Unit’s Firmware VERY IMPORTANTRemoving the X4 Modem FinishAppendix A Front and Back Panel InformationBack Panel Front PanelLights when LAN connection is active Blinks when unit is transmitting or receiving dataBlinks when unit is performing its startup sequence stays on solid when unit is connected to the ADSL lineConfiguring Your Browser Click Start Settings Control PanelAppendix B Internet ExplorerNext A dialog box describing your LAN Internet configuration displays. Uncheck the box Automatic discovery of proxy server and click Next Netscape Navigator In the Preferences dialog box, click the Advanced optionand then click Proxies click OK Select the option Direct connection to the Internet andWindows 95, Macintosh, and Linux Users Configuring Your TCP/IP SettingsWindows 95 TCP/IP Settings Appendix Cthe Select Network Component Type dialog box Macintosh TCP/IP Settings For Mac OS 7.6.1 - 9.2.2 and Above but not OS3 In the Configurations dialog box, click Duplicate For Mac OS Linux TCP/IP Settings For RedHatNETCONFIG, NETDEV0, and IFCONFIG0 For SuSEFor Debian Add this line to the file /etc/network/interfaces iface eth0 inetTroubleshooting Appendix DPROBLEM Why do I hear static or noise when I’m using my telephone? Appendix E Regulatory InformationDeclaration of Conformity Electrostatic Discharge Statement3372-A 272632002