Manuals / Zoom / Computer Equipment / Modem

Zoom X4 manual Appendix E, Regulatory Information, Declaration of Conformity, Directive, Standard

Models: X4

1 56

Download 56 pages 29.83 Kb

Page 55

Appendix E

Regulatory Information

Declaration of Conformity

The manufacturer declares under sole responsibility that this equipment is compliant to Directive 1999/5/EC (R&TTE Directive) via the following:

Directive	Standard	Test Report

73/23/EEC-Low	IEC 60950: 3rd ed. 1999	electrical safety
Voltage

89/336/EEC-EMC	EN 55024: 1998ed	EMC-immunity

89/336/EEC-EMC	EN 55022 : 1998ed ;	EMC-emissions
	EN 61000-3-2:1998 ed; A1, A2;
	EN 61000-3-3: 1995 ed

This product is CE Marked.

Electrostatic Discharge Statement

The unit may require resetting after a severe electrostatic discharge event.

Additional compliance information is located on the CD.

Appendix E: Regulatory Information

55

Image 55

Zoom X4 manual Appendix E, Regulatory Information, Declaration of Conformity, Electrostatic Discharge Statement, Directive

Contents

U S E R ’ S M A N U A L ADSL ModemCopyright 2002 All rights reserved Contents 1.1 Important! Before you Begin Installation Instructions1.2 Package Contents To Connect via the Ethernet Option Install the software before connecting the hardware1.3 Quick Start Instructions You Will Also NeedPWR ON OFF RESET ETHERNET PHONE ADSLpanel All hardware connections originate from the modem’s backPage To Connect via the USB Option b Click the ADSL Modem Installation Wizard buttonEstablishing Communication with the Hardware Installation disclaimer box or a DigitalNote You may see a Found New Hardware box Remember The User Name and Password are case- sensitive User Name=admin Password=zoomadslwith your X4. This page provides details about your Internet Using Phone Filters 1.4 If You Need Help 2.1 How To Use the Advanced Options Advanced Setup Options2.2 WAN Settings Chapter 2 Advanced Setup Options Static IP Address Permanent VC Virtual Circuit SettingsEnabled? ATM Service CategoryIGMP Internet Group Management Protocol Default GatewayEncapsulation BridgeDHCP Dynamic Host Configuration Protocol 2.3 LAN SettingsDHCP Address Pool IP AddressSubnet Mask DHCP ServerAction 2.4 NAT FirewallSession Name User’s IP2.5 Virtual Server 3 Select the Port Type. For FTP, it is TCP, which is the default Note These TCP/IP instructions and screenshot are typical of a computer using Windows 2000 or XP if you are using Windows 98 or Me, yours may differ slightly. If you are using Windows 95, or are a Macintosh or Linux user, and need help with your TCP/IP settings, turn to the Appendix on page 46. Otherwise, continue to Step 2.6 DMZ 10.0.0.15 Default gateway X4’s LAN IP addressChapter 2 Advanced Setup Options IP addressUser Configuration 2.7 DNSDNS Proxy Selection Wiring Selection 2.8 ADSL ConfigurationEnabled by default Default is Autosense - G.dmt first2.9 Miscellaneous HTTP server port Advanced Setup page and LAN Settingsaccess WAN side HTTP server3.1 Monitoring System Status System AdministrationChapter 3 System Administration 3.2 Monitoring ADSL StatusHighlight Release in the pulldown menu, and then click Save Changes View System Log 3.3 Performing System Administration TasksChange the Admin Password Perform a Diagnostic Test3.4 Resetting the Unit to Its Default Settings VERY IMPORTANT 3.5 Updating the Unit’s FirmwareFinish Removing the X4 ModemFront Panel Appendix AFront and Back Panel Information Back Panelsolid when unit is connected to the ADSL line Lights when LAN connection is activeBlinks when unit is transmitting or receiving data Blinks when unit is performing its startup sequence stays onInternet Explorer Configuring Your BrowserClick Start Settings Control Panel Appendix BNext A dialog box describing your LAN Internet configuration displays. Uncheck the box Automatic discovery of proxy server and click Next In the Preferences dialog box, click the Advanced option Netscape Navigatorand then click Proxies Select the option Direct connection to the Internet and click OKAppendix C Windows 95, Macintosh, and Linux Users Configuring YourTCP/IP Settings Windows 95 TCP/IP Settingsthe Select Network Component Type dialog box For Mac OS 7.6.1 - 9.2.2 and Above but not OS Macintosh TCP/IP Settings3 In the Configurations dialog box, click Duplicate For Mac OS For RedHat Linux TCP/IP SettingsAdd this line to the file /etc/network/interfaces iface eth0 inet NETCONFIG, NETDEV0, and IFCONFIG0For SuSE For DebianAppendix D TroubleshootingPROBLEM Why do I hear static or noise when I’m using my telephone? Electrostatic Discharge Statement Appendix ERegulatory Information Declaration of Conformity27263 3372-A2002