Husqvarna 16 manual Replacing the cutting unit belts, Belt change on BioClip

Page 33

MAINTENANCE

Replacing the cutting unit belts

Belt change on BioClip 103

There are two versions of BioClip 103. Version 1 has one toothed belt and version 2 has two. The toothed belts drive the blades and synchronise their rotation. The belts are located under a cover on top of the cutting unit.

1.Remove the cutting unit, see page 30.

2.Remove the front bolt from the parallel strut and tip the strut backwards. Push the height adjustment strut forwards.

3.Loosen the two bolts holding the protective hood and then lift off the hood.

Useful hint: Mark the positions of the blades on the respective pulley using a felt-tip pen.

4.Version 1:

Loosen the three bolts 1/2 - 1 turn. Press the sides of the belt together to give maximum slack and tighten one of the bolts. Replace the belt and tighten as shown (see decal on cover). Set the blades at 90º to each other and loosen the bolt again. The spring ensures the correct belt tension. Check the positions of the blades again and adjust if necessary by repositioning the belt on the teeth. Tighten the three bolts to 45 Nm.

4.Version 2:

Loosen the nuts on the eccentric plate and turn this away.

Loosen the four nuts (see diagram) holding the outer blade bearing enough so that the bearing can be moved.

Slide the blade bearing in towards the centre bearing and pry off the upper belt.

Repeat the procedure for the lower belt.

WARNING!

Wear gloves to protect your hands when working with the blades.

6017-154

BioClip 103 Version 1 and 2

6017-161

BioClip 103 Version 1 and 2

8009-173

BioClip 103 Version 1

6016-110

BioClip 103 Version 2

English – 31

Image 33

Contents Rider Svenska Contents Dear customer InstructionTravel and transport on public roads TowingGood service Safety InstructionsSerial number Engine TransmissionExplanation of Symbols General use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Throttle and Choke lever Speed limiterParking brake Lift lever for cutting unit Cutting unitLever for adjustment of cutting height SeatFuelling Driving Starting the engineCold engine Warm engine Driving the machine Cutting tips Release lever Stopping the engineMaintenance schedule MaintenanceDaily Maintenance interval HoursEngine hood Dismantling of the machine hoodsFront hood Right-hand fenderChecking and adjustment of the steering wires Adjusting the brakePoorly adjusted brakes can result in reduced braking power Replacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterProcedures on contact with acid Check the level of the battery acidChecking of the fuel pump’s air filter Ignition systemInspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureInstalling BioClip Fitting the cutting unitObserve caution to avoid trapping your hand Checking the cutting unit’s parallelism Removing the cutting unit Adjusting the parallelism of the cutting unitBelt change on BioClip Replacing the cutting unit belts6016-111 Placing in service position Service position for cutting unit6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Removal of BioClip plug Combi Replacing the break-pin BioClipLubrication Check the engine’s oil levelChanging the oil Lubricating the belt adjuster Check the transmission’s oil levelGeneral lubrication Problem Procedure Trouble Shooting ScheduleService StorageWinter storage Technical Data EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityPre-delivery service Servicejournal RiderAfter first 5 hours Work done Date, mileage, stamp, signServicejournal Servicejournal Servicejournal ´+H$¶6k¨ Page 114 00