Husqvarna manual 6016-111

Page 34

MAINTENANCE

5.Version 2:

Assembly: First fit the lower belt and then the upper belt.

Ensure the blades are positioned as set out in the diagram, at 90 degrees to each other, otherwise the belts must be adjusted. When the blade bearings are loose the belts can be moved around to the next tooth.

Tighten the nuts enough so that the bearings rest against the cutting hood but still can be moved.

Tension the belt by turning the eccentric adjuster on top of the cutting hood. Tighten the nut.

Tighten all nuts on the blade bearings.

6.Version 2:

When the belt can be moved 7 mm inwards using a force of 10 N the belt is adjusted correctly.

7.Version 1 och 2:

Fit the protective cover over the belts and replace the parallelism arm.

Belt replacement on BioClip 90

The BioClip 90 is driven by a toothed belt that synchronises rotation of the blades. The belt is located under the cover of the cutting unit.

When changing the belt on a BioClip 90 follow steps 1-7 of the above procedure for version 2. NOTE! BioClip 90 has just 1 belt.

Belt change on cutting unit with side or rear ejection and Combi 112

On these cutting units with "collision-proof" blades, the blades are driven by one V-belt. Do as follows to change the V-belt:

1.Remove the cutting unit, see page 30.

2.Undo the bolt on the lift strut and the two screws on the cover. Lift the cover off the cutting unit.

3.Loosen the spring that tensions the V-belt and pry off the belt.

Simply reverse the procedure to fit the new belt.

6016-111

IMPORTANT INFORMATION

The blades on a BioClip unit should be set at 90 degrees to each other. In all other cases the blades can collide and cause serious damage to the cutting unit.

6012-079

8009-287

6012-080

32 – English

Image 34

Contents Rider Svenska Contents Travel and transport on public roads InstructionDear customer TowingSerial number Safety InstructionsGood service Engine TransmissionExplanation of Symbols Safety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Speed limiter Throttle and Choke leverParking brake Cutting unit Lift lever for cutting unitSeat Lever for adjustment of cutting heightFuelling Starting the engine DrivingCold engine Warm engine Driving the machine Cutting tips Stopping the engine Release leverDaily Maintenance interval MaintenanceMaintenance schedule HoursFront hood Dismantling of the machine hoodsEngine hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Checking and adjustment of the throttle wire Replacement of the fuel filterDo not use compressed air to clean the paper filter Replacing the air filterChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Ignition systemInspecting the safety system Checking the tyre pressure Check the engine’s cooling air intakeFitting the cutting unit Installing BioClipObserve caution to avoid trapping your hand Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unit Removing the cutting unitReplacing the cutting unit belts Belt change on BioClip6016-111 Service position for cutting unit Placing in service position6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Replacing the break-pin BioClip Removal of BioClip plug CombiCheck the engine’s oil level LubricationChanging the oil Check the transmission’s oil level Lubricating the belt adjusterGeneral lubrication Trouble Shooting Schedule Problem ProcedureStorage ServiceWinter storage Technical Data EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeAfter first 5 hours Servicejournal RiderPre-delivery service Work done Date, mileage, stamp, signServicejournal Servicejournal Servicejournal ´+H$¶6k¨ Page 114 00