Husqvarna 16 manual Instruction, Dear customer, Travel and transport on public roads, Towing

Page 4

INSTRUCTION

Dear customer

Thank you for choosing a Husqvarna Rider. Husqvarna Riders are built to a unique design with a front- mounted cutting unit and a patented rear-wheel steering system. Riders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine.

We hope you will find this operator’s manual very useful. By following its instructions (on operation, service, maintenance, etc.) you will significantly extend the life of the machine and even its second-hand value.

When you sell your Rider, make sure you pass on the operator’s manual to the new owner.

Travel and transport on public roads

Check the relevant road traffic regulations before driving the machine on a public road. If transporting the machine on another vehicle always use approved securing devices and make sure that the machine is securely held.

Towing

When your machine is equipped with a hydrostatic transmission you should, if necessary, only tow the machine over short distances and at a low speed, otherwise there is a risk of damaging the transmission.

Intended use

This machine is designed solely for cutting grass on conventional lawns and other cleared and leveled ground without obstacles, as rocks, stumps etc., and, in conjunction with accessories supplied by the manufacturer even for other special tasks for which instructions are delivered with the accessory. Use in any other way is considered as contrary to the intended use. Compliance with and strict adherence to the conditions of operation, service and repair as specified by the manufacturer also constitute essential elements of the intended use.

This machine should be operated, serviced and repaired only by persons who are familiar with its particular characteristics and who are acquainted with the relevant safety procedures.

Accident prevention regulations, all other generally recognised regulations on safety and occupational medicine, and all road traffic regulations must be observed at all times.

Any arbitrary modifications carried out to this machine may relieve the manufacturer of liability for any resulting damage or injury

2 – English

Page 3 Page 5
Image 4
Page 3 Page 5
Contents Rider Svenska Contents Instruction Dear customerTravel and transport on public roads TowingSafety Instructions Good serviceSerial number Engine TransmissionExplanation of Symbols Safety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Speed limiter Throttle and Choke leverParking brake Cutting unit Lift lever for cutting unitSeat Lever for adjustment of cutting heightFuelling Starting the engine DrivingCold engine Warm engine Driving the machine Cutting tips Stopping the engine Release leverMaintenance Maintenance scheduleDaily Maintenance interval HoursDismantling of the machine hoods Engine hoodFront hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Checking and adjustment of the throttle wire Replacement of the fuel filterDo not use compressed air to clean the paper filter Replacing the air filterCheck the level of the battery acid Procedures on contact with acidChecking of the fuel pump’s air filter Ignition systemInspecting the safety system Checking the tyre pressure Check the engine’s cooling air intakeFitting the cutting unit Installing BioClipObserve caution to avoid trapping your hand Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unit Removing the cutting unitReplacing the cutting unit belts Belt change on BioClip6016-111 Service position for cutting unit Placing in service position6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Replacing the break-pin BioClip Removal of BioClip plug CombiCheck the engine’s oil level LubricationChanging the oil Check the transmission’s oil level Lubricating the belt adjusterGeneral lubrication Trouble Shooting Schedule Problem ProcedureStorage ServiceWinter storage Technical Data EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeServicejournal Rider Pre-delivery serviceAfter first 5 hours Work done Date, mileage, stamp, signServicejournal Servicejournal Servicejournal ´+H$¶6k¨ Page 114 00
Top Page Image Contents