Husqvarna 16 manual Servicejournal Rider, Pre-delivery service, After first 5 hours

Page 46

		SERVICEJOURNAL RIDER 16

	Work done		Date, mileage, stamp, sign
	Pre-delivery service
	1.	Top up battery with acid and recharge for four hours.
	2.	Fit steering wheel, seat and any optional equipment.
	3.	Adjust cutting unit:
		Adjust the lifting springs (the “weight” of the cutting unit should
		be 12-15 kg). Only applies to BioClip.
		Adjust cutting unit so that rear edge is about 2–4 mm higher
		than front edge.
		Adjust cutting unit height setting so that cutting height limit is
		5 mm above the frame of the unit at the lowest cutting height.
	4.	Check that engine has correct amount of oil.
	5.	Check that the right amount of oil is in the transmission.
	6.	Check and adjust tyre pressure (60 kPa, 0.6 bar).
	7.	Connect battery.
	8.	Fill with fuel and start engine.
	9.	Check that machine does not move in neutral.
	10. Check:
		Forward drive.
		Reverse drive.
		Operation of blades.
		Seat safety switch.
		Lift lever safety switch.
		Safety switch for the hydrostat pedals.
	11. Check engine revs 2 950 rpm.
	12. Tell customer about:		Pre-delivery service carried out.
		Need and benefits of following the service schedule.	No outstanding problems.
		Need and benefits of following the service schedule.
		The need and advantages of leaving the machine for regular	Certified:
		The need and advantages of leaving the machine for regular
		service.
		The effects of maintenance on the machine’s second hand
		value.
		Range of applications for BioClip.
	13. Complete proof of sale, etc.

	After first 5 hours
	1.	Change engine oil.

44 – English

Image 46

Contents Rider Svenska Contents Travel and transport on public roads InstructionDear customer TowingSerial number Safety InstructionsGood service Engine TransmissionExplanation of Symbols Safety instructions General useKeep children away from the area to be mowed Driving on slopes Proceed as followsMaintenance ChildrenDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Speed limiter Throttle and Choke leverParking brake Cutting unit Lift lever for cutting unitSeat Lever for adjustment of cutting heightFuelling Starting the engine DrivingCold engine Warm engine Driving the machine Cutting tips Stopping the engine Release leverDaily Maintenance interval MaintenanceMaintenance schedule HoursFront hood Dismantling of the machine hoodsEngine hood Right-hand fenderAdjusting the brake Checking and adjustment of the steering wiresPoorly adjusted brakes can result in reduced braking power Checking and adjustment of the throttle wire Replacement of the fuel filterDo not use compressed air to clean the paper filter Replacing the air filterChecking of the fuel pump’s air filter Check the level of the battery acidProcedures on contact with acid Ignition systemInspecting the safety system Checking the tyre pressure Check the engine’s cooling air intakeFitting the cutting unit Installing BioClipObserve caution to avoid trapping your hand Checking the cutting unit’s parallelism Adjusting the parallelism of the cutting unit Removing the cutting unitReplacing the cutting unit belts Belt change on BioClip6016-111 Service position for cutting unit Placing in service position6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Replacing the break-pin BioClip Removal of BioClip plug CombiCheck the engine’s oil level LubricationChanging the oil Check the transmission’s oil level Lubricating the belt adjusterGeneral lubrication Trouble Shooting Schedule Problem ProcedureStorage ServiceWinter storage Technical Data EU-DECLARATION of Conformity EU declaration of conformity Only applies to EuropeAfter first 5 hours Servicejournal RiderPre-delivery service Work done Date, mileage, stamp, signServicejournal Servicejournal Servicejournal ´+H$¶6k¨ Page 114 00