Husqvarna 16 manual Replacing the break-pin BioClip, Removal of BioClip plug Combi

Page 39

MAINTENANCE

Replacing the break-pin (BioClip)

The blades are fitted with a break-pin to protect the BioClip unit and its drive when colliding with obstacles. A domed, spring friction washer is fitted to each blade bolt. The washer must always be replaced with a new washer if the blade bolt is loosened. Otherwise the break-pin can break causing the blades to collide.

Only use original spare parts. A set containing a blade, break-pin and friction washer can be purchased from your dealer.

1.Put the unit in the service position, see ”Placing in the service position”.

2.Remove the blade (2A) by removing the blade bolt with washer and friction washer (2B).

3.Remove the remains of the broken break-pin (3).

4.Make sure the contact surfaces (4) on the blade and the blade mounting are free from metal. Clean if necessary.

5.Fit one new break-pin (5) in the blade mounting.

6.Fit the blade (6), make sure it is fitted as illustrated.

7.Fit a new friction washer (7) with the concave face turned towards the blade.

8.Fit the blade bolt with washer (8). Tightening torque 45-50 Nm (4,5-5 kpm)

Removal of BioClip plug (Combi)

To change a Combi unit from BioClip function to cutting unit with rear ejection, remove the BioClip plug located under the unit with three screws.

1.Put the unit in the service position, see "Placing in the service position".

2.Remove the three screws holding the BioClip plug, and remove the plug.

3.Tip: Fit three full-thread screws M8x15 mm in the screw holes to protect the threads.

4.Replace the unit in normal position.

Fit the BioClip plug in the reverse order.

5

3

2A

4

6

4

7

2B

8

8009-137

6017-227

Service position

8009-289

Removal of BioClip plug

English – 37

Image 39

Contents Rider Svenska Contents Towing InstructionDear customer Travel and transport on public roadsEngine Transmission Safety InstructionsGood service Serial numberExplanation of Symbols General use Safety instructionsKeep children away from the area to be mowed Proceed as follows Driving on slopesChildren MaintenanceDo not smoke when carrying out maintenance Transport Presentation PresentationLocation of the controls Throttle and Choke lever Speed limiterParking brake Lift lever for cutting unit Cutting unitLever for adjustment of cutting height SeatFuelling Driving Starting the engineCold engine Warm engine Driving the machine Cutting tips Release lever Stopping the engineHours MaintenanceMaintenance schedule Daily Maintenance intervalRight-hand fender Dismantling of the machine hoodsEngine hood Front hoodChecking and adjustment of the steering wires Adjusting the brakePoorly adjusted brakes can result in reduced braking power Replacement of the fuel filter Checking and adjustment of the throttle wireReplacing the air filter Do not use compressed air to clean the paper filterIgnition system Check the level of the battery acidProcedures on contact with acid Checking of the fuel pump’s air filterInspecting the safety system Check the engine’s cooling air intake Checking the tyre pressureInstalling BioClip Fitting the cutting unitObserve caution to avoid trapping your hand Checking the cutting unit’s parallelism Removing the cutting unit Adjusting the parallelism of the cutting unitBelt change on BioClip Replacing the cutting unit belts6016-111 Placing in service position Service position for cutting unit6017-221 6017-222 8009-122 6017-223 Restoring from service position Checking the blades Removal of BioClip plug Combi Replacing the break-pin BioClipLubrication Check the engine’s oil levelChanging the oil Lubricating the belt adjuster Check the transmission’s oil levelGeneral lubrication Problem Procedure Trouble Shooting ScheduleService StorageWinter storage Technical Data EU declaration of conformity Only applies to Europe EU-DECLARATION of ConformityWork done Date, mileage, stamp, sign Servicejournal RiderPre-delivery service After first 5 hoursServicejournal Servicejournal Servicejournal ´+H$¶6k¨ Page 114 00