Husqvarna 155, 155 AWD Explanation of Symbols and Decals, Xxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx

Page 9

EXPLANATION OF SYMBOLS AND DECALS

These symbols are found on the machine and in the operator’s manual.

Study them carefully so that you know what they mean.

WARNING!

Xxxxxxx xxxx xxxxxxxx xxx x Xxxxx xxxxxx xx.

xx xxxxxxxx xxxxx xxx xx.

Used in this publication to notify the reader of a risk of personal injury or death, particularly if the reader should neglect to follow instructions given in the manual.

IMPORTANT INFORMATION

Xxxxxxx xxxx xxxxxxxx xxx xxx

xxxx xxxxxx xx.

Used in this publication to notify the reader of a risk of material damage, particularly if the reader should neglect to follow instructions given in the manual.

Used also when there is a potential for misuse or misassembly.

Read the operator’s manual

N

Neutral

Fast

Slow

Engine off

Oil level

 

Cutting height

Backwards

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Hydrostatic free wheel

Use eye and hearing protection

Never use the machine if persons, especially

Never carry passengers on the

children, or animals, are in the vicinity.

machine or equipment.

Keep hands and feet away from

Drive very slowly

moving parts.

without the cutting unit.

 

STARTING INSTRUCTION

READ OPERATOR´S MANUAL.

CHECK ENGINE OIL LEVEL.

ENGAGE PARKING BRAKE AND LIFT CUTTING DECK IN TRANSPORT POSITION.

IF ENGINE IS COLD USE CHOKE.

START THE ENGINE.

RELEASE PARKING BRAKE BEFORE DRIVING.

INSTRUCTIONS DE DEMARRAGE

LIRE LE GUIDE DE CONDUITE.

VÉRIFIEZ LE NIVEAU D´HUILE MOTEUR.

SERREZ LE FREIN DE PARKING ET METTRE LE CARTER DE COUPE EN POSITION HAUT.

SI LE MOTEUR EST FROID, UTILISEZ LE STARTER.

ACTIONNEZ LE DÉMARREUR.

DESSERREZ LE FREIN DE PARKING

ChokeFuel

ForwardsIgnition

Parking brake

Warning

 

Warning!

Never drive across a

 

Risk that the

slope

machine can tip over

 

 

 

 

 

 

 

 

 

Use protective glasses

Use protective gloves

Speed limiter pedal forwards

Neutral

Speed limiter pedal reverse

Switch off the engine and take off the ignition cable before repairs or maintenance

English – 7

Image 9
Contents Rider 155 Rider 155 AWD Page Contents Introduction Good Service Manufacturing NumberEngine Transmission General operation Safe operation practices for ride-on mowersII. Slope operation III. ChildrenSafe handling of gasoline IV. ServiceTravel and transport on public roads Towing of the machineIntended use Xxxxxxx xxxx xxxxxxxx xxx Xxxx xxxxxx Explanation of Symbols and DecalsPlacards Safety Instructions Safety InstructionsSafety Instructions Slope Operation Personal Safety EquipmentChildren Maintenance General Maintenance Always use protective glasses when handling the battery Transport Customer responsibilities Location of the controls ControlsThrottle and Choke lever Speed limiterParking brake Lift lever for the cutting unit Cutting unitLever for adjustment of cutting height SeatRefueling Before starting OperationStarting the engine Cold engineWarm engine To remove cables, reverse order To start an engine with a weak batteryRunning Moving tips MAX1015 Stopping the engineRelease lever Rear AxleFront Axle Maintenance schedule MaintenanceAvoid using a high pressure washer or a steam cleaner Cleaning and washingEngine hood Dismantling of the machine hoodsFront hood Right-hand fenderChecking and adjustment of the steering wires Adjusting the Parking Brake Rider 155 AWD Adjusting the parking brakeInspecting the muffler Adjusting the throttle wireReplacing the air filter Replacement of the fuel filterProcedures on contact with acid Check the level of the battery acidFitting the wrong spark plug type can damage the engine Ignition systemChecking the safety system Main fuse Checking the tire pressureCheck the engine’s cooling air intake Observe caution to avoid trapping your hand Fitting the cutting unitChecking the cutting unit’s parallelism Removing the cutting unit Adjusting the parallelism of the cutting unitService position for the cutting unit Placing in service positionBelt replacement on the cutting unit Remove the two support wheels from under the front hood 8009-122 6017-223 6017-225 6017-226 Checking the blades Restoring from service positionRemoval of BioClip plug Combi Lubrication Check the engine’s oil levelChanging the oil Check the transmission’s oil level Change of oil filterGeneral lubrication Lubricating the belt adjusterProblem Procedure Trouble Shooting ScheduleStorage ServiceWinter storage CoverTechnical Data Technical Data Pre-delivery service ServicejournalAfter first 5 hours Work done Date, mileage, stamp, sign´z+R23¶5L¨ Page 115 01