RedMax CHTZ2401-CA, CHTZ2401L-CA manual Working Plan, Before Starting the Engine

Page 10

English

5. For safe operation

working area.

c.During rain, during storms at times of strong or gale-force winds, or at any other times when weather conditions might make it unsafe to use the product.

■WORKING PLAN

1.You should never use the product when under the influence of alcohol, when suffering from exhaustion or lack of sleep, when suffering from drowsiness as a result of having taken cold medicine or at any other time when a possibility exists that your judgment might be impaired or that you might not be able to operate the product properly and in a safe manner.

2.When planning your work schedule, allow plenty of time to rest. Limit the amount of time over which the product is to be used continuously to somewhere around 30 ~ 40 minutes per session, and take 10 ~ 20 minutes of rest between work sessions. Also try to keep the total amount of work performed in a single day under 2 hours or less.

WARNING

1.If you don’t observe the working time, or working manner (See “USING THE PRODUCT”), Repetitive Stress Injury (RSI) could occur.

If you feel discomfort, redness and swelling of your fingers or any other part of your body, see a doctor before getting worse.

2.To avoid noise complaints, in general, operate product between 8 a.m. and 5 p.m. on weekdays and 9 a.m. to 5 p.m. on weekends.

NOTE

Check and follow the local regulations as to sound level and hours of operations for the product.

■BEFORE STARTING THE ENGINE

1.The area within a perimeter of 15 m (50 ft) of the person using the product should be considered a hazardous area into which no one should enter. If necessary, yellow warning rope, warning signs should be placed around the perimeter of the area. When work is to be performed simultaneously by two or more persons, care should also be taken to constantly look around or otherwise check for the presence and locations of other people working so as to maintain a distance between each person

10

Image 10

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsModel Especificaciohes Emplacement des pieces Situación de las piezasFiche technique ModeloSymbols on the machine Emplacement PosiciónWorking Condition For safe operationWorking Circumstance Condición DE Trabajo Conditions DE TravailCircunstancias DE Trabajo Working Plan Before Starting the EnginePlan DE Trabajo Plan DE TravailAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineUtilisation DE LA Machine Demarrage DU MoteurArranque DE LA Máquina Empleo DEL ProductoManual MaintenanceIf Someone Comes SI SE Acerca Alguien SI QUELQU’UN S’APPROCHEEntretien MantenimientoRefill after cooling the engine Handling FuelTransportation Manejo DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Proporción DE LA Mezcla Recomendada Gasolina 50 Aceite Rapport DE Melange Recommande Essence 50 HuileLors de l’utilisation de la véritable huile RedMax/ZENOAH Al utilizar el aceite auténtico de RedMax/ZENOAHHOW to MIX Fuel Fueling the UnitComo Mezclar EL Combustible Comment Obtenir UN BON MelangeRemplissage DU Reservoir Abastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteStarting Engine OperationOP3 7 6 Cutting head will start moving upon the engine startsFonctionnement Uso Running in the Engine Adjusting Idling SpeedStopping Engine OP3 Air filterReglage DU Ralenti Arret DU MoteurFonctionnement DU Moteur Apagado DEL MotorDo not press the throttle during this operation HOW to USEHandle CHTZ2401/CHTZ2401-CA only Handle Locking leverProcedure Dutilisation Manette CHTZ2401/CHTZ2401-CA Cómo UsarVertical cut Hedge Trimming TechniquesHorizontal cut Corte vertical Coupe horizontaleTécnicas DE Recorte Corte horizontalMaintenance Maintenance ChartTableau D’ENTRETIEN Tabla DE MantenimientoFuel Filter Replacement Plug is NGK CMR7H or Champion RZ7CAIR Filter Spark PlugBougie D’ALLUMAGE Filtre a AIRFiltre a Carburant Filtro DE AireIntake AIR Cooling Vent BladesVentilación DE Refrigeración DEL Aire DE Admisión Ouïe DE Refroidissement PAR AIRLames CuchillasSharpening MA8 Safety Lock MA7Reduction Gearbox Verrou DE Sécurité MA7 Dispositivo DE Seguridad MA7 Affûtage MA8Afilado MA8 Reducteur MA9Disposal Procedures to be Performed After Every 100 Hours of USEStorage ANTI-VIBRATION SystemRangement Entretien MantenimientoAlmacenamiento 11. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Nota RemarqueParts list Cutting Unit HTZ2401/HTZ2401-CA HTZ2401-L/HTZ2401-L-CA S/N Parts list CHTZ2401-L/CHTZ2401-L-CA Parts list Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Control DE Emisiones Emission ControlMesures DE Lutte Contre LES Emissions CHTZ2401-CA/CHTZ2401L-CA