RedMax CHTZ2401-CA, HTZ2401L-CA AIR Filter, Fuel Filter, Spark Plug, Tightening Torque Muffler

Page 34

English

8. Maintenance

WARNING

MA1(1)

MA2

(1)

MA3

.025 in

0.655mm

•Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury.

■AIR FILTER

•The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one. (MA1)

(1) air filter

■FUEL FILTER

•When the engine runs short of fuel supply, check the fuel cap and the fuel filter for blockage. (MA2)

(1) fuel filter

■SPARK PLUG

•Starting failure and mis-firing are often caused by a fouled spark plug. Clean the spark plug and check that the plug gap is in the correct range. For a replacement plug, use the correct type specified by RedMax. (MA3)

•REPLACEMENT PLUG IS NGK CMR7H OR CHAMPION RZ7C.

IMPORTANT

•Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine becoming overheated and damaged.

•To install the spark plug, first turn the plug until it is finger tight, then tighten it a quarter turn more with a socket wrench.

TIGHTENING TORQUE:

■MUFFLER

WARNING

87~121 in-lbs (9.8~13.7 N.m.)

•Inspect periodically, the muffler for loose fasteners, any damage or corrosion. If any sign of exhaust

34

Image 34

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsModel Especificaciohes Emplacement des pieces Situación de las piezasFiche technique ModeloSymbols on the machine Emplacement PosiciónWorking Condition For safe operationWorking Circumstance Condición DE Trabajo Conditions DE TravailCircunstancias DE Trabajo Working Plan Before Starting the EnginePlan DE Trabajo Plan DE TravailAvant DE Mettre LE Moteur EN Marche Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineUtilisation DE LA Machine Demarrage DU MoteurArranque DE LA Máquina Empleo DEL ProductoManual MaintenanceIf Someone Comes SI SE Acerca Alguien SI QUELQU’UN S’APPROCHEEntretien MantenimientoRefill after cooling the engine Handling FuelTransportation Manejo DEL Combustible Manipulation DU CarburantTransport Llenar una vez que el motor se haya enfriadoFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Proporción DE LA Mezcla Recomendada Gasolina 50 Aceite Rapport DE Melange Recommande Essence 50 HuileLors de l’utilisation de la véritable huile RedMax/ZENOAH Al utilizar el aceite auténtico de RedMax/ZENOAHHOW to MIX Fuel Fueling the UnitComo Mezclar EL Combustible Comment Obtenir UN BON MelangeRemplissage DU Reservoir Abastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteStarting Engine OperationOP3 7 6 Cutting head will start moving upon the engine startsFonctionnement Uso Running in the Engine Adjusting Idling SpeedStopping Engine OP3 Air filterReglage DU Ralenti Arret DU MoteurFonctionnement DU Moteur Apagado DEL MotorDo not press the throttle during this operation HOW to USEHandle CHTZ2401/CHTZ2401-CA only Handle Locking leverProcedure Dutilisation Manette CHTZ2401/CHTZ2401-CA Cómo UsarVertical cut Hedge Trimming TechniquesHorizontal cut Corte vertical Coupe horizontaleTécnicas DE Recorte Corte horizontalMaintenance Maintenance ChartTableau D’ENTRETIEN Tabla DE MantenimientoFuel Filter Replacement Plug is NGK CMR7H or Champion RZ7CAIR Filter Spark PlugBougie D’ALLUMAGE Filtre a AIRFiltre a Carburant Filtro DE AireIntake AIR Cooling Vent BladesVentilación DE Refrigeración DEL Aire DE Admisión Ouïe DE Refroidissement PAR AIRLames CuchillasSharpening MA8 Safety Lock MA7Reduction Gearbox Verrou DE Sécurité MA7 Dispositivo DE Seguridad MA7 Affûtage MA8Afilado MA8 Reducteur MA9Disposal Procedures to be Performed After Every 100 Hours of USEStorage ANTI-VIBRATION SystemRangement Entretien MantenimientoAlmacenamiento 11. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Nota RemarqueParts list Cutting Unit HTZ2401/HTZ2401-CA HTZ2401-L/HTZ2401-L-CA S/N Parts list CHTZ2401-L/CHTZ2401-L-CA Parts list Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Control DE Emisiones Emission ControlMesures DE Lutte Contre LES Emissions CHTZ2401-CA/CHTZ2401L-CA