RedMax HTZ2401L-CA, HTZ2401-CA Handling Fuel, Refill after cooling the engine, Transportation

Page 16

English

5. For safe operation

always be sure to use only RedMax products or products which have been certified by RedMax for use with the RedMax product.

4.In the event that any part must be replaced or any maintenance or repair work not described in this manual must be performed, please contact a representative from the store nearest RedMax authorized servicing dealer for assistance.

5.Do not use any accessory or attachment other than those bearing the RedMax mark and recommended for the unit.

6.Under no circumstances should you ever take apart the product or alter it in any way. Doing so might result in the product becoming damaged during operation or the product becoming unable to operate properly.

■HANDLING FUEL

1.The engine of the RedMax product is designed to run on a mixed fuel, which contains highly flammable gasoline. Never store cans of fuel or refill the tank of the unit in any place where there is a boiler, stove, wood fire, electrical sparks, welding sparks, or any other source of heat or fire which might ignite the fuel.

2.Never smoke while operating the unit or refilling its fuel tank.

3.When refilling the tank, always turn off the engine and allow it to cool down. Take a careful look around to make sure that there are no sparks or open flames anywhere nearby before refueling.

(1) Refill after cooling the engine.

4.Wipe spilled fuel completely using a dry rag if any fuel spillage occurs during refueling.

5.After refueling, screw the fuel cap back tightly onto the fuel tank and then carry the unit to a spot 3 m or more away from where it was refueled before turning on the engine.

6.Do not inhale fuel fumes as they are toxic.

■TRANSPORTATION

1.When hand-carrying the product, cover over the cutting part if necessary, lift up the product and carry it paying attention to the blade.

2.Never transport the product over rough roads over long distances by vehicle without removing all fuel from the fuel tank. If doing so, fuel might leak from the tank during transport.

16

Image 16

Contents OWNER/OPERATOR Manual Mode D’EMPLOI Manual DE Instrucciones Contents Tables des matieres Contenido Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOIAdvertencias Contenidas EN EL Manual Parts location SpecificationsModel Emplacement des pieces Situación de las piezas Fiche techniqueEspecificaciohes ModeloSymbols on the machine Emplacement PosiciónWorking Condition For safe operationWorking Circumstance Condición DE Trabajo Conditions DE TravailCircunstancias DE Trabajo Working Plan Before Starting the EnginePlan DE Travail Avant DE Mettre LE Moteur EN MarchePlan DE Trabajo Antes DE Arrancar LA MáquinaUsing the Product Starting the EngineDemarrage DU Moteur Arranque DE LA MáquinaUtilisation DE LA Machine Empleo DEL ProductoManual MaintenanceIf Someone Comes SI QUELQU’UN S’APPROCHE EntretienSI SE Acerca Alguien MantenimientoRefill after cooling the engine Handling FuelTransportation Manipulation DU Carburant TransportManejo DEL Combustible Llenar una vez que el motor se haya enfriadoFuel When using RedMax/ZENOAH genuine oilRecommended Mixing Ratio Gasoline 50OIL Rapport DE Melange Recommande Essence 50 Huile Lors de l’utilisation de la véritable huile RedMax/ZENOAHProporción DE LA Mezcla Recomendada Gasolina 50 Aceite Al utilizar el aceite auténtico de RedMax/ZENOAHHOW to MIX Fuel Fueling the UnitComo Mezclar EL Combustible Comment Obtenir UN BON MelangeRemplissage DU Reservoir Abastecimiento DE LA Unidad For Your Engine LIFE, Avoid Eviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteOperation OP3 7 6Starting Engine Cutting head will start moving upon the engine startsFonctionnement Uso Adjusting Idling Speed Stopping Engine OP3Running in the Engine Air filterArret DU Moteur Fonctionnement DU MoteurReglage DU Ralenti Apagado DEL MotorHOW to USE Handle CHTZ2401/CHTZ2401-CA onlyDo not press the throttle during this operation Handle Locking leverProcedure Dutilisation Manette CHTZ2401/CHTZ2401-CA Cómo UsarVertical cut Hedge Trimming TechniquesHorizontal cut Coupe horizontale Técnicas DE RecorteCorte vertical Corte horizontalMaintenance Maintenance ChartTableau D’ENTRETIEN Tabla DE MantenimientoReplacement Plug is NGK CMR7H or Champion RZ7C AIR FilterFuel Filter Spark PlugFiltre a AIR Filtre a CarburantBougie D’ALLUMAGE Filtro DE AireIntake AIR Cooling Vent BladesOuïe DE Refroidissement PAR AIR LamesVentilación DE Refrigeración DEL Aire DE Admisión CuchillasSharpening MA8 Safety Lock MA7Reduction Gearbox Affûtage MA8 Afilado MA8Verrou DE Sécurité MA7 Dispositivo DE Seguridad MA7 Reducteur MA9Procedures to be Performed After Every 100 Hours of USE StorageDisposal ANTI-VIBRATION SystemRangement Entretien MantenimientoAlmacenamiento 11. Guía de localización y solución de problemas Troubleshooting guideGuide de localisation des pannes Nota RemarqueParts list Cutting Unit HTZ2401/HTZ2401-CA HTZ2401-L/HTZ2401-L-CA S/N Parts list CHTZ2401-L/CHTZ2401-L-CA Parts list Cylinder Comp Manufacturer’s warranty coverage Owner’s warranty responsibilitiesCouverture de la garantie constructeur Obligations du propriétaire liées à la garantieCobertura de la garantía dada por el fabricante Responsabilidades del propietarioLimited Warranty Garantie limitée Garantía Limitada Emission Control Mesures DE Lutte Contre LES EmissionsControl DE Emisiones CHTZ2401-CA/CHTZ2401L-CA