Makita BCM2600 Emissions Component Defect Warranty Coverage, Parts Covered, What is not Covered

Page 3

5. Maintenance

Any warranted part which is not scheduled for replacement as required maintenance or which is scheduled only for regular inspec- tion to the effect of “repair or replace as necessary” shall be war- ranted as to defects for the warranty period. Any warranted part which is scheduled for replacement as required maintenance shall be warranted as to defects only for the period of time up to the first scheduled replacement for that part. Any replacement part that is equivalent in performance and durability may be used in the perfor- mance of any maintenance or repairs. The owner is responsible for the performance of all required maintenance, as defined in the Makita owner’s manual.

6. Consequential Coverage

Coverage hereunder shall extend to the failure of any engine compo- nents caused by the failure of any warranted part still under warranty.

EMISSIONS COMPONENT DEFECT WARRANTY COVERAGE

MAKITA U.S.A. Inc. (MAKITA) warrant to the initial retail purchaser and each subsequent owner, that this utility equipment was designed, built, and equipped to conform at the time of initial sale to all applicable regulations of the U.S. Environmental Protection Agency (EPA), and that the engine is free of defects in materials and workmanship which would cause this engine to fail to conform with EPA regulations during its warranty period.

For the components listed under PARTS COVERED, the service dealer authorized by MAKITA will, at no cost to you, make the neces- sary diagnosis, repair, or replacement necessary to ensure that the engine complies with applicable U.S. EPA regulations.

EMISSISON COMPONENT DEFECT WARRANTY PERIOD

The warranty period for this engine begins on the date of sale to the initial purchaser and continues for a period of 2 years.

PARTS COVERED

Listed below are the parts covered by the Emission Components Defect Warranty. Some of the parts listed below may require sched- uled maintenance and are warranted up to the first scheduled replacement point for that part.

(1)Fuel Metering System

(i)Carburetor and internal parts

(ii)Fuel filter, if applicable.

(iii)Throttle stopper, if applicable.

(iv)Choke System, if applicable.

(2)Air Induction System

(i)Air cleaner plate

(ii)Air cleaner case

(3)Ignition System

(i)Spark plugs.

(ii)Flywheel Magneto

(iii)Ignition Coil.

(4)Miscellaneous Items Used in Above Systems

(i)Fuel hoses, clamps and sealing gaskets

OBTAINING WARRANTY SERVICE

To obtain warranty service, take your engine to the nearest MAKITA Factory Service Center or service Center authorized by MAKITA. Bring your sales receipts indicating date of purchase for this engine. The dealer of service authorized by MAKITA will perform the neces- sary repairs or adjustments within a reasonable amount of time and furnish you with a copy of the repair order. All parts and accessories replaced under this warranty become the property of MAKITA.

WHAT IS NOT COVERED

Conditions resulting from tampering, misuse, improper adjustment (unless they were made by the service dealer authorized by MAKITA during a warranty repair), alteration, accident, failure to use the rec- ommended fuel and oil, or not performing required maintenance services.

-The replacement parts used for required maintenance services.

-Consequential damages such as loss of time, inconvenience, loss of use of the engine or equipment, etc.

-Diagnosis and inspection charges that do not result in war- ranty-eligible service being performed.

-Any non-authorized replacement part, or malfunction of autho- rized parts due to use of non-authorized parts.

OWNER’S WARRANTY RESPONSIBILITIES

As the engine owner, you are responsible for the performance of the required maintenance listed in your owner's manual. MAKITA recom- mends that you retain all receipts covering maintenance on your engine, but MAKITA cannot deny warranty solely for the lack of receipts or for your failure to ensure the performance of all sched- uled maintenance. As the engine owner, you should however be aware that MAKITA may deny warranty coverage if your engine or a part has failed due to abuse, neglect, improper maintenance or unap- proved modifications.

You are responsible for presenting your engine to the nearest service dealer authorized by MAKITA when a problem exists.

If you have any questions regarding your warranty rights and respon- sibilities, you should contact the followings :

*For the nearest Makita service center, please visit www.makitatools.com

*For technical support or questions regarding operation of our tools and accessories call: 1-800-4-MAKITA

*Makita USA Inc. Corporate Office : 14930 Northam St. La Mirada, CA 90638-5753

(For Canada)

*For the authorized service centre nearest you please refer to the local yellow pages directory under “tools”, or contact our customer service department Tel 1-800-263-3734 (Canada only), or visit our web site www.makita.ca

*Makita Canada Inc. Head Office & Plant : 1950 Forbes Street, Whitby, ON L1N 7B7

THINGS YOU SHOULD KNOW ABOUT THE EMISSION CONTROL SYSTEM WARRANTY:

MAINTENANCE AND REPAIRS

You are responsible for the proper maintenance of the engine. You should keep all receipts and maintenance records covering the per- formance of regular maintenance in the event questions arise.

These receipts and maintenance records should be transferred to each subsequent owner of the engine. MAKITA reserves the right to deny warranty coverage if the engine has not been properly main- tained. Warranty claims will not be denied, however, solely because of the lack of required maintenance or failure to keep maintenance records.

MAINTENANCE, REPLACEMENT OR REPAIR OF EMISSION CON- TROL DEVICES AND SYSTEMS MAY BE PERFORMED BY ANY REPAIR ESTABLISHMENT OR INDIVIDUAL; HOWEVER, WARRANTY REPAIRS MUST BE PERFORMED BY A SERVICE DEALER AUTHO- RIZED BY MAKITA. THE USE OF PARTS THAT ARE NOT EQUIVA- LENT IN PERFORMANCE AND DURABILITY TO AUTHORIZED PARTS MAY IMPAIR THE EFFECTIVENESS OF THE EMISSION CONTROL SYSTEM AND MAY HAVE A BEARING ON THE OUTCOME OF A WAR- RANTY CLAIM.

If other than the parts authorized by MAKITA are used for mainte- nance replacements or for the repair of components affecting emis- sion control, you should assure yourself that such parts are warranted by their manufacturer to be equivalent to the parts autho- rized by MAKITA in their performance and durability.

HOW TO MAKE A CLAIM

All repair qualifying under this limited warranty must be performed by a service dealer authorized by MAKITA. In the event that any emis- sion-related part is found to be defective during the warranty period, you shall notify MAKITA at the following contacts and you will be advised of the appropriate warranty service dealer or service provid- ers where the warranty repair can be performed.

*For the nearest Makita service center , please visit www.makitatools.com

*For technical support or questions regarding operation of our tools and accessories call: 1-800-4-MAKITA

*Makita USA Inc. Corporate Office : 14930 Northam St. La Mirada, CA

90638-5753 (For Canada)

*For the authorized service centre nearest you please refer to the local yellow pages directory under “tools”, or contact our customer service department Tel 1-800-263-3734 (Canada only), or visit our web site www.makita.ca

*Makita Canada Inc. Head Office & Plant : 1950 Forbes Street, Whitby, ON L1N 7B7

3

Image 3
Contents Importante Recommandation importanteEnglish Table of contentsMakita U.S.A. Inc. Warranty Coverage Owner’s Warranty ResponsibilitiesWhat is not Covered Emissions Component Defect Warranty CoverageEmissison Component Defect Warranty Period Obtaining Warranty ServiceSymbols ON/STARTOFF/STOP Personal protective equipment Safety InstructionsGeneral Instructions Intended use of the machineKickback prevention RefuelingMethod of operation KickbackTechnical Data Maintenance instructionsFirst Aid For machines with Loop Handle Mounting of HandleMounting of Protector For machines with U Handle modelsFor # BCM2600 and # BCM3300 Installing Cutter-BladeInstalling Nylon cutting head Mounting of Cutter Blade or Nylon Cutter HeadCorrect Handling of Machine FUELS/REFUELINGRE-SHARPENING the Cutting Tool Points in Operation and HOW to StopIdle Speed Adjustment StoppingServicing Instructions Nylon Cutting HeadSuction head in the fuel tank Cleaning of muffler exhaust portStorage Supply of grease to gear caseTroubleshooting Chart Maintenance ScheduleResponsabilités envers la garantie du propriétaire FrançaisCalifornie Seulement Étendue de la garantie de Makita U.S.A. IncDemande Dapplication DE LA Garantie CE QUE LA Garantie NE Couvre PASPériode DE Garantie Contre LES Vices DES Pièces À Émission Pièces Couvertes PAR LA GarantiePour Faire Appliquer LA Garantie Symboles MARCHE/DÉMARRAGEArrêt Dispositifs de protection personnelle Consignes DE SécuritéConsignes générales Utilisation prévue pour loutilPrévention des chocs en retour RemplissageUtilisation Choc en retourModèle Données TechniquesInstructions dentretien Premiers secoursDiam. dandain 41 cm 16 po 43 cm 17 po Poignée Type Pour les modèles à poignée en boucle Assemblage DE LA PoignéeAssemblage DU Protecteur Pour les modèles à poignée en UPour les modèles BCM2310/CA, BCM2610/CA et BCM3310/CA Installation de la lame du sécateurInstallation de la tête de coupe en nylon Pour les modèles BCM2600 et BCM3300Comment Tenir Loutil CARBURANTS/REMPLISSAGEArrêt Réglage DE LA Vitesse DE Rotation À VideRaffûtage DE Loutil Tranchant Instructions Pour LA Réparation Tête DE Coupe EN NylonNettoyage de lorifice de sortie du silencieux RangementGraissage du carter dengrenage Crépine daspiration du réservoir de carburantTableau DE Dépannage Horaire DentretienResponsabilidades del propietario para la garantía EspañolCalifornia Solamente Cobertura de la garantía de Makita U.S.A. IncResponsabilidades DEL Propietario DE LA Garantía Partes Cubiertas POR LA GarantíaObtención DEL Servicio DE Garantía QUÉ no Cubre LA GarantíaCómo Hacer UNA Reclamación ENCENDIDO/INICIO SímbolosEquipo de protección personal Instrucciones DE SeguridadInstrucciones generales Uso previsto para la máquinaPrevención contra los retrocesos bruscos RepostajeMétodo de operación Retroceso bruscoDatos Técnicos Instrucciones de mantenimientoPrimeros auxilios Pulgadas Conjunto del asidero Tipo Redondo En U Para máquinas con asidero redondo Montaje DEL AsideroMontaje DEL Protector Para máquinas del modelo con asideros en UInstalación del disco de corte Montaje DEL Disco DE Corte O Cabezal DEL Cordón DE NylonPara # BCM2600 y # BCM3300 Para # BCM2310/CA, BCM2610/CA y BCM3310/CAManejo Correcto DE LA Máquina COMBUSTIBLE/REPOSTAJEAfilado DEL Implemento DE Corte Puntos a Tener EN Cuenta EN LA Operación Y Cómo PararParada Ajuste DE LA Velocidad AL RalentíInstrucciones DE Mantenimiento Cabezal DEL Cordón DE NylonLimpieza del orificio de escape del silenciador AlmacenamientoSuministro de grasa a la caja de engranajes La cabeza de succión del depósito de combustiblePrograma DE Mantenimiento Gráfico DE Solución DE Problemas
Related manuals
Manual 44 pages 54.66 Kb