Makita BCM2600, BCM3300 Storage, Supply of grease to gear case, Suction head in the fuel tank

Page 13

Supply of grease to gear case

Supply grease (Shell Albania 3 or equivalent ) to the gear case through the grease hole every 30 hours.

Suction head in the fuel tank

The fuel filter (A) of the suction head is for filtering the fuel to the carburetor. A periodical visual inspection of this fuel filter is highly recommended.

To inspect the fuel filter, open the tank cap and pull out the suction head through the opening of the tank using a wire hook.

If the filter is found to have hardened, polluted or clogged up, it should be replaced.

Insufficient fuel supply caused by the deteriorated filter will result in the poor performance of the engine. It is therefore important to replace the fuel filter at least quarterly to ensure fuel-supply to the carburetor.

Cleaning of muffler exhaust port

Check the muffler exhaust port (B) regularly. If it is clogged by carbon deposits, scratch out the deposits carefully with a suitable tool.

STORAGE

When the Brush Cutter/String Trimmer is in storage for a long time,

1Drain all fuel from the fuel tank into a container approved for gasoline. Run the engine until it stops.

2Clean all foreign material from the machine and store it in a well-venti- lated place that is not accessible to children.

B

A

13

Image 13
Contents Importante Recommandation importanteMakita U.S.A. Inc. Warranty Coverage Table of contentsOwner’s Warranty Responsibilities EnglishEmissison Component Defect Warranty Period Emissions Component Defect Warranty CoverageObtaining Warranty Service What is not CoveredON/START SymbolsOFF/STOP General Instructions Safety InstructionsIntended use of the machine Personal protective equipmentMethod of operation RefuelingKickback Kickback preventionMaintenance instructions Technical DataFirst Aid Mounting of Protector Mounting of HandleFor machines with U Handle models For machines with Loop HandleInstalling Nylon cutting head Installing Cutter-BladeMounting of Cutter Blade or Nylon Cutter Head For # BCM2600 and # BCM3300Correct Handling of Machine FUELS/REFUELINGIdle Speed Adjustment Points in Operation and HOW to StopStopping RE-SHARPENING the Cutting ToolServicing Instructions Nylon Cutting HeadStorage Cleaning of muffler exhaust portSupply of grease to gear case Suction head in the fuel tankTroubleshooting Chart Maintenance ScheduleCalifornie Seulement FrançaisÉtendue de la garantie de Makita U.S.A. Inc Responsabilités envers la garantie du propriétairePériode DE Garantie Contre LES Vices DES Pièces À Émission CE QUE LA Garantie NE Couvre PASPièces Couvertes PAR LA Garantie Demande Dapplication DE LA GarantiePour Faire Appliquer LA Garantie MARCHE/DÉMARRAGE SymbolesArrêt Consignes générales Consignes DE SécuritéUtilisation prévue pour loutil Dispositifs de protection personnelleUtilisation RemplissageChoc en retour Prévention des chocs en retourInstructions dentretien Données TechniquesPremiers secours ModèleDiam. dandain 41 cm 16 po 43 cm 17 po Poignée Type Assemblage DU Protecteur Assemblage DE LA PoignéePour les modèles à poignée en U Pour les modèles à poignée en boucleInstallation de la tête de coupe en nylon Installation de la lame du sécateurPour les modèles BCM2600 et BCM3300 Pour les modèles BCM2310/CA, BCM2610/CA et BCM3310/CAComment Tenir Loutil CARBURANTS/REMPLISSAGERéglage DE LA Vitesse DE Rotation À Vide ArrêtRaffûtage DE Loutil Tranchant Instructions Pour LA Réparation Tête DE Coupe EN NylonGraissage du carter dengrenage RangementCrépine daspiration du réservoir de carburant Nettoyage de lorifice de sortie du silencieuxTableau DE Dépannage Horaire DentretienCalifornia Solamente EspañolCobertura de la garantía de Makita U.S.A. Inc Responsabilidades del propietario para la garantíaObtención DEL Servicio DE Garantía Partes Cubiertas POR LA GarantíaQUÉ no Cubre LA Garantía Responsabilidades DEL Propietario DE LA GarantíaCómo Hacer UNA Reclamación ENCENDIDO/INICIO SímbolosInstrucciones generales Instrucciones DE SeguridadUso previsto para la máquina Equipo de protección personalMétodo de operación RepostajeRetroceso brusco Prevención contra los retrocesos bruscosInstrucciones de mantenimiento Datos TécnicosPrimeros auxilios Pulgadas Conjunto del asidero Tipo Redondo En U Montaje DEL Protector Montaje DEL AsideroPara máquinas del modelo con asideros en U Para máquinas con asidero redondoPara # BCM2600 y # BCM3300 Montaje DEL Disco DE Corte O Cabezal DEL Cordón DE NylonPara # BCM2310/CA, BCM2610/CA y BCM3310/CA Instalación del disco de corteManejo Correcto DE LA Máquina COMBUSTIBLE/REPOSTAJEParada Puntos a Tener EN Cuenta EN LA Operación Y Cómo PararAjuste DE LA Velocidad AL Ralentí Afilado DEL Implemento DE CorteInstrucciones DE Mantenimiento Cabezal DEL Cordón DE NylonSuministro de grasa a la caja de engranajes AlmacenamientoLa cabeza de succión del depósito de combustible Limpieza del orificio de escape del silenciadorPrograma DE Mantenimiento Gráfico DE Solución DE Problemas
Related manuals
Manual 44 pages 54.66 Kb