Andis Company AGRC manual To change the blade drive assembly, Do not overtighten

Page 9

Diagram N

Diagram O

Diagram P

Diagram Q

Diagram R

Diagram S

changing the blade DRIVE assembly

If your clipper blades no longer cut properly (be sure to try more than one blade, since blade currently being used may be dull), it could be that your blade drive assembly needs replacement.

To change the blade drive assembly:

1.Remove blade set (Diagram N).

2.Remove drive cap (Diagram O).

3.Remove blade drive mounting screws (Diagram P).

4.	NOTE: Before removing blade drive assembly, note the way it is positioned	Diagram T

(this will help you in reassembly). Remove blade drive assembly (Diagram Q).

5.Drive bearing should be at its lowest position, if not, move it with your finger to lowest position (Diagrams R & S).

6.Put on new drive assembly, align screw holes and press down (Diagram Q).

7.Reassemble blade drive by replacing mounting screws, turning just until snug (Diagram S).

Do not overtighten.

8.Replace drive cap (Diagram O).

9.Replace blade (Diagram T).

factory repair service

When the blades of your Andis Clipper become dull after repeated use, it is advisable to send your blades to an Andis Authorized Service Station for resharpening. If you wish your clipper to be serviced as well, they should be carefully packed and mailed either Parcel Post Insured, or U.P.S.

9

Image 9

Contents USE and Care Proper Battery Disposal Battery pack removal and preparation for recyclingTHIS PRODUCT IS INTENDED FOR COMMERCIAL USE Model Agrv Cord Pack Use Model Agrc Cord Pack UseBefore initial use battery pack must be charged for a Model AGR+ With Battery UseRead the Following Before Charging this Clipper Minimum of one hourProblem Charger does not fully charge the battery Guidelines for Battery Pack and Charger USERefresh That has developed a memory to perform like newTo work Much longer than one that does not. Andis suggests thatRemoving blade set OPERATING INSTRUCTIONSCare and servicing of your andis Clipper blades To change the blade drive assembly Replace drive cap Diagram O Replace blade Diagram TDo not overtighten Peligro Para reducir el riesgo de descarga eléctrica Precauciones importantesUso del paquete de cables del modelo Agrc Guarde Estas InstruccionesEliminación Adecuada DE LAS Baterías Este Producto Está Indicado Para USO ComercialUso del paquete de cables del modelo Agrv Modelo AGR+ con uso de la batería LEA LO Siguiente Antes DE Cargar Esta RecortadoraLuz verde de parpadeo corto Pautas Para EL USO DEL Paquete DE Baterías Y EL Cargador Problema El cargador no carga la batería completamenteBotón Actualizar USO DE LA Función DE ActualizaciónInstrucciones DE Operación Desmontaje DEL Juego DE HojasReemplazo O Cambio DEL Juego DE Hojas Responsable en el caso de lesión debido a este descuido Cambio DEL Conjunto DE Accionamiento DE LAS Hojas Servicio DE Reparación EN FábricaPara cambiar el conjunto de accionamiento de las hojas La remplacer Mises en garde importantesUtilisation du cordon modèle Agrc Conserver CES InstructionsMise AU Rebut Correcte DES Piles CE Produit EST Réservé À UN Usage CommercialUtilisation du cordon modèle Agrv Lire CE QUI Suit Avant DE Charger LA Tondeuse Modèle AGR+ avec batteriePendant 1 heure minimum Vert, clignotements rapprochésConsignes DE Sécurité Relatives À LA Batterie ET AU Chargeur Utilisation DE LA Fonction DE Rafraîchissement Bouton deRafraîchissement Maintenance Utilisateur Mode D’EMPLOIRemplacement OU Changement DU JEU DE Lames Retrait DU JEU DE LamesPar suite de telles négligences Entretien DES Lames DE LA Tondeuse AndisService DE Réparation EN Usine Remplacement DE L’ENTRAÎNEMENT DE LA LameAndis Company Manufacturer’s 12 Month Limited Warranty