DeWalt DPD3000IC, N0003431 Refer to Chemicals and Cleaning Solvents, Turn the water source on

Page 13

4. Verify the filter screen (U) is in water inlet of pump.

The cone side faces out. 5. Connect the cold water source (V) to pump inlet.

NOTE: Water source must provide a minimum of 5 gallons per minute at 20 pSI (138 kPa).

Warning: To reduce the possibility of contami-

U

nation always protect against backflow when con-

 

nected to a potable water system.

 

6.

Connect high-pressure hose (P) to pump

P

 

outlet.

7.

If applying a chemical or cleaning solution,

 

 

refer to Chemicals and Cleaning Solvents.

 

8.

Turn the water source on.

 

Caution: Risk of property damage. Failure to

V

do so could cause damage to the pump.

 

9.Remove all air from the pump and high pressure hose by depress- ing trigger until a steady stream of water is present.

10.Turn the engine ON/OFF switch (H) to the ON position.

11.Place the fuel valve lever (M) in the ON postion.

12.If the engine is cold, move the choke (K) to the CLOSED position as shown.

Note: Do not allow the starter grip to snap back. Return it gently by hand.

Warning: Risk of unsafe operation. If engine does not start after two pulls, squeeze trigger of gun to relieve pump pressure. Pull starter cord slowly until resistance is felt. Then pull cord rapidly to avoid kickback and prevent hand or arm injury.

Note: If the oil level in the engine is low, the engine will not start. If the engine does not start, check the oil level and add oil as needed.

14. As the engine warms up, move the choke to

the open position. 15. Depress trigger on gun to start water flow.

Warning: Risk of unsafe operation. Stand on a stable surface and grip gun/wand firmly with both hands. Expect the gun to kickback when triggered.

16. Release trigger to stop water flow.

DANGER: Risk of injury from spray. Engage the

trigger lock (X) when gun is not in use to prevent X accidental spraying.

17. Adjust spray for the task being performed by changing quick connect nozzle. Refer to

English

H

M

K

Spray Wand Nozzles.

Shutting Down

1.If chemicals were applied, place the chemical hose into a container of clean water and draw clean water through chemical injection system to rinse system thoroughly.

Caution: Risk of property damage Failure to do so could cause

13.Warning: Risk of unsafe operation. Pull starter grip slowly until resistance is felt. Then pull starter grip (I) rapidly to avoid kickback and prevent hand or arm injury.

damage to the pump.

2. Place the engine ON/OFF switch (H) to the OFF Position.

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Guide Dutilisation Manual de instrucciones CAT 3DNX27GSI Engine Pump SpecificationsOil Use DP70 Oil Capacity 8.5 oz ml Definitions Safety Guidelines SpecificationsImportant Safety Instructions Operators What can happen How to prevent itWhat can happen Use only accessories rated When using replacementOthers Result in injection injuriesHand and arm injury Kickback causing seriousIf engine does not start after Two pulls, squeeze triggerOr trailers What can happen How to prevent itThis product For Future USEHeavy to be lifted by one Pressure Washer Assembly Fig InstallationPressure Adjustments OperationChanging Nozzles on Spray Wand Chemicals and Cleaning SolventsTo apply chemicals and solvents Starting Start-up ProcedurePlace the engine ON/OFF switch H to the OFF Position Refer to Chemicals and Cleaning SolventsTurn the water source on How To Change Pump Oil MaintenanceEngine Pump To Check OilTo Remove Tires To Clean the Water Inlet FilterSTORAGE Engine Pump Limited Warranty Accessories Service InformationPressure Washer RepairsEnglish Problem Code Troubleshooting GuideGlossary Possible Solution Troubleshooting CodesCode Possible cause Spray wand not in low pressure Panneau Moteur Porte-buse Caractéristiques techniques de la pompePoignée de démarrage MoteurDéfinitions lignes directrices en Matière de sécurité Fiche techniqueDirectives de sécurité importantes Ce qui peut se produire Conserver CES DirectivesLaisser environ 127 mm De l’équipement et pro Du matériel déposé contreVoquer une surchauffe et Haute pression dans uneSuite Ce qui peut se produireNe pas utiliser de produit Démarrage correcte pour Suivre la procédure deQui provoquerait ainsi une Au brasCe qui peut se produire Comment l’éviter Avertissement Risque d’éclatementAssemblage de la laveuse haute pression Fig Fonctionnement FonctionnementRéglages de la pression Buses du tube de pulvérisation FigChangement DES Buses SUR LE Tube DE Pulvérisation Produits chimiques et solvants de nettoyageApplication DE Produits Chimiques ET Solvants Démarrage Chimique ou de nettoyant, se reporter à la Procédure DE DémarrageSection Produits chimiques et solvants de Nettoyage Ouvrir l’approvisionnement en eauEnfoncer la détente du pistolet pour activer le jet d’eau EntretienRelâcher la détente pour arrêter le jet d’eau Pompe MoteurVérification DU Niveau D’HUILE Méthode DE Vidange DE L’HUILE DE LA PompeRetrait des pneu Nettoyage du filtre de l’admission d’eauRangement Laveuse haute pressionRéparations Accessoires Information SUR LES RéparationsGarantie limitée ’utilisateur de changer rapidement les buses haute pression GlossaireMoins 19 l/min 5 gallons par minute Guide de dépannage Solution ProbableCodes de dépannage Problème CodeCodes de dépannage suite Produit chimique trop épais Especificaciones de la bomba MotorAceite Use DP70 Capacidad de aceite 251 ml 8,5 onzas Definiciones Normas de seguridad EspecificacionesInstrucciones de seguridad importantes Peligro Riesgo de explosión o incendio Conserve Estas Instrucciones¿Qué puede suceder? Cómo evitarlo Peligro Riesgo Respiratorio asfixia Peligro Riesgo DE Inyección DE Líquido y laceración Peligro Riesgo de operación insegura Puede retroceder, lo que Si no se sigue elLas manos y los brazos Si el motor no arrancaAdvertencia Riesgo DE superficies calientes Advertencia Riesgo de de estallidoAdvertencia Riesgo de quemadura química Ensamblado de la lavadora a presión Fig¿Qué puede suceder? Advertencia Riesgo DE descarga eléctricaAjustes a la presión OperaciónBoquillas para la varilla pulverizadora Fig De alta presión P aCambio DE LAS Boquillas DE LA Varilla Pulverizadora Productos químicos y solventes de limpiezaPara Aplicar Productos Químicos Y Solventes Puesta en marchaQuímicos y solventes de limpieza Procedimiento DE Puesta EN MarchaSuelte el disparador para detener el flujo de agua ApagadoBomba MantenimientoLimpieza de las boquillas Para Controlar EL AceitePara quitar los neumáticos Para limpiar el filtro de entrada de aguaAlmacenamiento Accesorios Lavadora a presiónInformación DE Mantenimiento Fecha y lugar de compraPóliza de Garantía ReparacionesGarantía limitada Identificación DEL ProductoCULIACAN, SIN Glosario Códigos de detección de problemas Guía de detección de problemasProblema Código Código Causa posibleCódigos de detección de problemas continuar Español Español Page Page FEB08 Form No. N0003431 DPD3000IC Copyright 2008 D eWALT EWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD
Top Page Image Contents