DeWalt N0003431, DPD3000IC Maintenance, Engine Pump, To Check Oil, How To Change Pump Oil

Page 14

3. Place the fuel valve lever (M) in the OFF postion.

Change pump oil after the first 10 hours of operation and every 250 hours thereafter.

English

Caution: Risk of property damage. Never turn water supply off while pressure washer engine is running or damage to pump will result.

4. Turn water source off.

5. Pull trigger on spray gun to relieve any water pressure in hose or spray gun.

6. Refer to Storage for proper storage procedures.

MAINTENANCE

WARNING: Risk of burning. When performing maintenance, you may be exposed to hot surfaces, water pressure or moving parts that can cause serious injury or death.

To Check Oil

The oil level should come to the dot in the middle of the sight glass (AA).

How To Change Pump Oil

1.Loosen pump oil fill plug (BB).

2.Place a container under the oil drain plug (CC).

3.Remove pump oil drain plug.

4.After oil is drained, replace oil drain plug. Tighten securely.

BB

AA

CC

WARNING: Risk of fire. Always disconnect, spark plug wire, let the engine cool and release all water pressure before performing any maintenance or repair. The engine contains flammable fuel. Do not smoke or work near open flames while performing maintenance.

To ensure efficient operation and longer life of your pressure washer, a routine maintenance schedule should be prepared and followed. If the pressure washer is used in unusual conditions, such as high temperatures or dusty conditions, more frequent­ maintenance checks will be required.

Engine

Consult the engine instruction manual for the manu­fac­tur­er's­ recom- mendations for any and all maintenance.

NOTE: The pressure washer frame is equipped with an oil drain hole to help make changing the engine oil easier.

Pump

NOTE: The pump was filled with oil at the factory.

5.Remove pump oil plug and fill with 8.5 oz. (251 ml) of DP70 pump oil. If DP70 is not available use 30W non-detergent oil.

6.Replace pump oil plug and tighten securely.

Nozzle Cleaning

If the nozzle becomes clogged with foreign materials, such as dirt, excessive pressure may develop. If the nozzle becomes partially clogged or restricted, the pump pressure will pulsate. Clean the nozzle immediately using the nozzle kit supplied and the following instructions:

1.Shut off the pressure washer and turn off the water supply.

2.Pull trigger on gun handle to relieve any water pressure.

3.Disconnect the spray wand from the gun.

4. Remove the high-pressure nozzle from the

Y

spray wand. Remove any obstructions

 

with the nozzle cleaning tool (Y) provided

 

and back flush with clean water.

 

14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Guide Dutilisation Manual de instrucciones Oil Use DP70 Oil Capacity 8.5 oz ml Engine Pump SpecificationsCAT 3DNX27GSI Important Safety Instructions SpecificationsDefinitions Safety Guidelines What can happen How to prevent it OperatorsWhat can happen Others When using replacementUse only accessories rated Result in injection injuriesIf engine does not start after Kickback causing seriousHand and arm injury Two pulls, squeeze triggerWhat can happen How to prevent it Or trailersHeavy to be lifted by one For Future USEThis product Pressure Adjustments InstallationPressure Washer Assembly Fig OperationTo apply chemicals and solvents Chemicals and Cleaning SolventsChanging Nozzles on Spray Wand Start-up Procedure StartingTurn the water source on Refer to Chemicals and Cleaning SolventsPlace the engine ON/OFF switch H to the OFF Position Engine Pump MaintenanceHow To Change Pump Oil To Check OilSTORAGE Engine Pump To Clean the Water Inlet FilterTo Remove Tires Pressure Washer Accessories Service InformationLimited Warranty RepairsEnglish Glossary Troubleshooting GuideProblem Code Code Possible cause Troubleshooting CodesPossible Solution Spray wand not in low pressure Poignée de démarrage Caractéristiques techniques de la pompePanneau Moteur Porte-buse MoteurDirectives de sécurité importantes Fiche techniqueDéfinitions lignes directrices en Matière de sécurité Laisser environ 127 mm Conserver CES DirectivesCe qui peut se produire Voquer une surchauffe et Du matériel déposé contreDe l’équipement et pro Haute pression dans uneCe qui peut se produire SuiteNe pas utiliser de produit Qui provoquerait ainsi une Suivre la procédure deDémarrage correcte pour Au brasAvertissement Risque d’éclatement Ce qui peut se produire Comment l’éviterAssemblage de la laveuse haute pression Fig Réglages de la pression FonctionnementFonctionnement Buses du tube de pulvérisation FigApplication DE Produits Chimiques ET Solvants Produits chimiques et solvants de nettoyageChangement DES Buses SUR LE Tube DE Pulvérisation Démarrage Section Produits chimiques et solvants de Nettoyage Procédure DE DémarrageChimique ou de nettoyant, se reporter à la Ouvrir l’approvisionnement en eauRelâcher la détente pour arrêter le jet d’eau EntretienEnfoncer la détente du pistolet pour activer le jet d’eau Vérification DU Niveau D’HUILE MoteurPompe Méthode DE Vidange DE L’HUILE DE LA PompeRangement Nettoyage du filtre de l’admission d’eauRetrait des pneu Laveuse haute pressionGarantie limitée Accessoires Information SUR LES RéparationsRéparations Moins 19 l/min 5 gallons par minute Glossaire’utilisateur de changer rapidement les buses haute pression Codes de dépannage Solution ProbableGuide de dépannage Problème CodeCodes de dépannage suite Produit chimique trop épais Aceite Use DP70 Capacidad de aceite 251 ml 8,5 onzas MotorEspecificaciones de la bomba Instrucciones de seguridad importantes EspecificacionesDefiniciones Normas de seguridad ¿Qué puede suceder? Cómo evitarlo Conserve Estas InstruccionesPeligro Riesgo de explosión o incendio Peligro Riesgo Respiratorio asfixia Peligro Riesgo DE Inyección DE Líquido y laceración Peligro Riesgo de operación insegura Las manos y los brazos Si no se sigue elPuede retroceder, lo que Si el motor no arrancaAdvertencia Riesgo de de estallido Advertencia Riesgo DE superficies calientes¿Qué puede suceder? Ensamblado de la lavadora a presión FigAdvertencia Riesgo de quemadura química Advertencia Riesgo DE descarga eléctricaBoquillas para la varilla pulverizadora Fig OperaciónAjustes a la presión De alta presión P aProductos químicos y solventes de limpieza Cambio DE LAS Boquillas DE LA Varilla PulverizadoraPuesta en marcha Para Aplicar Productos Químicos Y SolventesProcedimiento DE Puesta EN Marcha Químicos y solventes de limpiezaApagado Suelte el disparador para detener el flujo de aguaLimpieza de las boquillas MantenimientoBomba Para Controlar EL AceiteAlmacenamiento Para limpiar el filtro de entrada de aguaPara quitar los neumáticos Información DE Mantenimiento Lavadora a presiónAccesorios Fecha y lugar de compraGarantía limitada ReparacionesPóliza de Garantía Identificación DEL ProductoCULIACAN, SIN Glosario Problema Código Guía de detección de problemasCódigos de detección de problemas Código Causa posibleCódigos de detección de problemas continuar Español Español Page Page EWALT Industrial Tool Co., 701 Joppa Road, Baltimore, MD FEB08 Form No. N0003431 DPD3000IC Copyright 2008 D eWALT
Top Page Image Contents