Craftsman 919.672240, D25083 owner manual Before Starting

Page 13

BEFORE STARTING

Read and understand all Important Safety Instructions in the front of this manual and the following Cautions and Warnings before starting the pressure washer.

Filler cap/dipstick

•Never fill fuel tank completely. Fill tank to 1/2" below bottom of filler neck to provide space for fuel expansion. Wipe any fuel spillage from engine and equipment before starting engine.

•Never fill fuel tank indoors. Never fill fuel tank when engine is running or hot. Do not smoke when filling fuel tank.

•Never run engine indoors or in enclosed, poorly ventilated areas. Engine exhaust con- tains carbon monoxide, an odorless and deadly gas.

•Never turn water supply off while pressure washer engine is running or damage to pump will result.

•DO NOT use hot water, use cold water only.

•DO NOT stop spraying water for more than two minutes at a time.

1.Add fresh high quality unleaded gasoline with a pump octane rat- ing of 86 or higher. Do not over- fill. Wipe up spilled fuel before starting the engine.

2.Remove filler cap/dipstick and add engine oil (supplied) to engine. NOTE: There will be a slight amount of oil in the engine from factory testing. Always check oil level before each start- up.

3.Verify the filter screen is in water inlet of pump, as shown.

Filter Screen

4.Connect high pressure hose to pump outlet.

5.Connect water source to pump inlet.

NOTE: Water source must provide a minimum of 5 gallons per minute at 20 p.s.i.

		High
Water		Pressure
Source		Hose

6.If you are applying a chemical or cleaning solution, See How To

Siphon Chemicals/Cleaning Solvents in Operation section of this manual.

7.Turn water source on.

NOTE: Make sure water supply is turned on.

13- ENG

D25083

Image 13

Contents Pressure Washer Table of Contents Safety Guidelines Definitions Specification ChartHazard Important Safety InstructionsRisk of Explosion or Fire Risk to BreathingRisk of Electrical Shock Risk of Unsafe OperationSpray directed at electrical outlets or Risk of Chemical Burn Risk to Fluid InjectionRisk of HOT Surfaces Assembly BOX ContentsRemove Loosen Pressure Washer OperationEngine Throttle Control Lever Controls engine speedPressure Washer Terminology To Adjust PressureTo USE Wand To Shut Down To Siphon CHEMICALS/CLEANING SolventsBefore Starting Maintenance Customer Responsibilities Table Maintenance TaskEngine Pressure WasherTo Change Oil CleaningInspect Pump Clean and Replace Spark PlugWand Engine Preparation StoragePeratures are Expected Problem Cause Correction Troubleshooting GuideSource on to remove all air From the hose. When thereWater source to pump inlet High pressure hose is tooProblem Cause Correction ENG Service and Repair Parts HOW to OrderGuide de l’utilisateur Garantie Table DES MatièresMesures DE Sécurité Définitions Tableau DES SpécificationsDe modèle 919.672240 Laveuse à pression MoteurRisque DE Feux OU Dexplosion Mesures DE Sécurité ImportantesRisque PAR Inhalation Risque DE Chocs Électriques Risque Dune Utilisation NON SécuritaireRisque DE Brûlures Chimiques Risque Dinjection DUN FluideDes brûlures graves Risque DE Surfaces ChaudesAssemblage Contenu DE LA BoîteRetirer Desserer Familiarisez-vous avec votre laveuse à pression UtilisationLaveuse À Pression MoteurUtilisation Terminologie DES Laveuses À PressionRéglage DE LA Pression Utilisation DE LA LanceSiphonnage DE Produits CHIMIQUES/SOLVANTS DE Nettoyage Arrêt DE LA Laveuse À PressionOuvrez le robinet de la source deau Avant LE Démarrage« OFF » EntretienTableau DES Responsabilités DU Client MoteurTache D’ENTRETIEN Vérification du niveau d’huileFiltre à air Changement de l’huileInspection NettoyagePompe Nettoyage et remplacement de la bougie d’allumageBuse Préparation du moteur EntreposageProblème Cause Correction Guide DE DépannageRetirez le boyau court de lorifice dentrée de la pompe 20- FR Tubes sont endommagés à Faire remplacer par un Cause du gel Csga = Centre de service sous garantie autorisé39- FR Composez LE Pour Pièces DE Rechange ET Service DE Réparation