Craftsman 919.672240, D25083 owner manual Troubleshooting Guide, Problem Cause Correction

Page 19

6.Pull engine starter rope slowly several times until antifreeze or windshield washer fluid comes out of high pressure hose con- nection of pump.

7.Remove short hose from water inlet of pump.

8.Install spark plug into spark plug hole and tighten securely, then reconnect spark plug wire.

9.Drain all water from high pressure hose, coil it, and store it in cradle of the pressure washer handle.

10.Drain all water from spray gun and wand by holding spray gun in a vertical position with nozzle end pointing down and squeezing trigger. Store in gun/hose holder.

11.Store chemical hose, high pres- sure hose, spray gun, and wand so they are protected from dam- age, such as being run over.

TROUBLESHOOTING GUIDE

	PROBLEM		CAUSE		CORRECTION

	Engine will not	1.	No fuel.	1.	Add Fuel.
	start	2.	Pressure builds up after	2.	Squeeze gun trigger to
		2.	Pressure builds up after	2.	Squeeze gun trigger to
			two pulls on the recoil		relieve pressure.
			starter or after initial use.
		3.	Not choked.	3.	Choke engine, place
					engine in the choke posi-
					tion.
		4.	Spark plug wire not	4.	Attach spark plug wire.
			attached.
		5.	Choke lever in the	5.	Move choke to the "No
			"Choke" position on a		Choke" position.
			"hot" engine or an engine
			that has been exposed to
			thermal heat for a long
			period of time.
		6.	Fuel valve closed	6.	Move the fuel valve knob
					to the "Open" position.

	No or low	1.	Wand not in high pres-	1.	See How to Use Wand
	pressure	1.	Wand not in high pres-	1.	See How to Use Wand
	pressure		sure.		paragraph in the
	(initial use)				Operation Section.
					Operation Section.
		2.	Low water supply.	2.	Water supply must be at
					least 5 GPM @ 20 PSI.
		3.	Leak at high pressure	3.	Repair leak. Apply sealant
			hose.		tape if necessary.
		4.	Nozzle obstructed.	4.	Clean nozzle with paper
					clip or nozzle cleaning
					tool, pour water into noz-
					zle end to flush out ob-
					struction.
		5.	Water filter screen	5.	Remove and clean filter.
			clogged.

19- ENG

D25083

Image 19

Contents Pressure Washer Table of Contents Safety Guidelines Definitions Specification ChartRisk to Breathing Important Safety InstructionsHazard Risk of Explosion or FireRisk of Electrical Shock Risk of Unsafe OperationSpray directed at electrical outlets or Risk of Chemical Burn Risk to Fluid InjectionRisk of HOT Surfaces Assembly BOX ContentsRemove Loosen Throttle Control Lever Controls engine speed OperationPressure Washer EnginePressure Washer Terminology To Adjust PressureTo USE Wand To Shut Down To Siphon CHEMICALS/CLEANING SolventsBefore Starting Maintenance Pressure Washer Maintenance TaskCustomer Responsibilities Table EngineTo Change Oil CleaningInspect Pump Clean and Replace Spark PlugWand Engine Preparation StoragePeratures are Expected Problem Cause Correction Troubleshooting GuideHigh pressure hose is too From the hose. When thereSource on to remove all air Water source to pump inletProblem Cause Correction ENG Service and Repair Parts HOW to OrderGuide de l’utilisateur Garantie Table DES MatièresMoteur Tableau DES SpécificationsMesures DE Sécurité Définitions De modèle 919.672240 Laveuse à pressionRisque DE Feux OU Dexplosion Mesures DE Sécurité ImportantesRisque PAR Inhalation Risque DE Chocs Électriques Risque Dune Utilisation NON SécuritaireRisque DE Brûlures Chimiques Risque Dinjection DUN FluideDes brûlures graves Risque DE Surfaces ChaudesAssemblage Contenu DE LA BoîteRetirer Desserer Moteur UtilisationFamiliarisez-vous avec votre laveuse à pression Laveuse À PressionUtilisation DE LA Lance Terminologie DES Laveuses À PressionUtilisation Réglage DE LA PressionSiphonnage DE Produits CHIMIQUES/SOLVANTS DE Nettoyage Arrêt DE LA Laveuse À PressionOuvrez le robinet de la source deau Avant LE Démarrage« OFF » EntretienVérification du niveau d’huile MoteurTableau DES Responsabilités DU Client Tache D’ENTRETIENNettoyage Changement de l’huileFiltre à air InspectionPompe Nettoyage et remplacement de la bougie d’allumageBuse Préparation du moteur EntreposageProblème Cause Correction Guide DE DépannageRetirez le boyau court de lorifice dentrée de la pompe 20- FR Tubes sont endommagés à Faire remplacer par un Cause du gel Csga = Centre de service sous garantie autorisé39- FR Composez LE Pour Pièces DE Rechange ET Service DE Réparation