Craftsman 919.672240 Customer Responsibilities Table, Maintenance Task, Engine, Pressure Washer

Page 15

CUSTOMER RESPONSIBILITIES TABLE

	Before		Every 25	Every 50	Every 100
	Before		hours or	hours or	hours or
MAINTENANCE TASK	each use		hours or	hours or	hours or
MAINTENANCE TASK	each use		yearly	yearly	yearly
			yearly	yearly	yearly
ENGINE
check oil level	X

change oil				X

check air filter			X
clean/replace spark plug					X

PRESSURE WASHER

check/clean inlet screen	X

check high pressure hose	X

check soap and chemical	X
hose and filter

check gun and wand for leaks	X

prepare for storage	Prepare unit for storage if it is to remain idle for longer
	than 30 days

ENGINE

To Check Oil

1.Shut down engine and place on a level surface.

2.Remove filler cap/dipstick and wipe it clean.

Filler cap/dipstick

3.Insert and remove the filler cap/dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.

Oil Filler

Cap/Dipstick

Upper Limit

Lower Limit

4.If the oil level is low, fill to the edge of the oil filler hole with the

SAE 10W-30 oil.

NOTE: Other viscosities shown in the chart may be used when the average temperature in your area is within the recommended range.

SAE Viscosity Grades

**

*

Synthetic 5W-30, 10W-30

F -20	0	20	32 40	60	80	100
C -30	-20	-10	0	10	20 30	40

STARTING TEMPERATURES RANGE

ANTICIPATED BEFORE NEXT OIL CHANGE

15- ENG

D25083

Image 15

Contents Pressure Washer Table of Contents Safety Guidelines Definitions Specification ChartRisk to Breathing Important Safety InstructionsHazard Risk of Explosion or FireRisk of Unsafe Operation Risk of Electrical ShockSpray directed at electrical outlets or Risk of Chemical Burn Risk to Fluid InjectionRisk of HOT Surfaces Assembly BOX ContentsRemove Loosen Throttle Control Lever Controls engine speed OperationPressure Washer EngineTo Adjust Pressure Pressure Washer TerminologyTo USE Wand To Shut Down To Siphon CHEMICALS/CLEANING SolventsBefore Starting Maintenance Pressure Washer Maintenance TaskCustomer Responsibilities Table EngineCleaning To Change OilInspect Clean and Replace Spark Plug PumpWand Storage Engine PreparationPeratures are Expected Problem Cause Correction Troubleshooting GuideHigh pressure hose is too From the hose. When thereSource on to remove all air Water source to pump inletProblem Cause Correction ENG Service and Repair Parts HOW to OrderGuide de l’utilisateur Garantie Table DES MatièresMoteur Tableau DES SpécificationsMesures DE Sécurité Définitions De modèle 919.672240 Laveuse à pressionMesures DE Sécurité Importantes Risque DE Feux OU DexplosionRisque PAR Inhalation Risque DE Chocs Électriques Risque Dune Utilisation NON SécuritaireRisque DE Brûlures Chimiques Risque Dinjection DUN FluideDes brûlures graves Risque DE Surfaces ChaudesAssemblage Contenu DE LA BoîteRetirer Desserer Moteur UtilisationFamiliarisez-vous avec votre laveuse à pression Laveuse À PressionUtilisation DE LA Lance Terminologie DES Laveuses À PressionUtilisation Réglage DE LA PressionSiphonnage DE Produits CHIMIQUES/SOLVANTS DE Nettoyage Arrêt DE LA Laveuse À PressionOuvrez le robinet de la source deau Avant LE Démarrage« OFF » EntretienVérification du niveau d’huile MoteurTableau DES Responsabilités DU Client Tache D’ENTRETIENNettoyage Changement de l’huileFiltre à air InspectionNettoyage et remplacement de la bougie d’allumage PompeBuse Préparation du moteur EntreposageGuide DE Dépannage Problème Cause CorrectionRetirez le boyau court de lorifice dentrée de la pompe 20- FR Tubes sont endommagés à Faire remplacer par un Cause du gel Csga = Centre de service sous garantie autorisé39- FR Composez LE Pour Pièces DE Rechange ET Service DE Réparation