Zenoah GZ400 Tensioner nut Chain cover, Moving Direction, Loosen Tighten Tensioner screw Lift up

Page 20

F6-4

F6-5

F6-6

English

6. Installing guide bar and saw chain

1.Pull the guard towards the front handle to check that the chain brake is not engaged.

2.Loosen the nuts and remove the chain cover.

3.Gear the chain to the sprocket and, while fitting the saw chain around the guide bar, mount the guide bar to the power unit. Adjust the position of the chain tensioner. (F6-4)

(1)Tensioner nut

(2)Chain cover

NOTE

Pay attention to the correct direction of the saw chain. (F6-5)

(1) Moving Direction

4.Fit the chain cover to the power unit and fasten the nuts to finger tightness.

5.While holding up the tip of the bar, adjust the chain tension by turning the tensioner screw until the tie straps just touch the bottom side of the bar rail.

(F6-6)

6.Tighten the nuts securely with the bar tip held up (12~15 N·m). Then check the chain for smooth rotation and proper tension while moving it by hand. If necessary, readjust with the chain cover loose.

7.Tighten the tensioner screw.

(2)Loosen

(3)Tighten

(4)Tensioner screw

(5)Lift up

NOTE

A new chain will expand its length in the beginning of use. Check and readjust the tension frequently as a loose chain can easily derail or cause rapid wear of itseif and the guide bar.

20

Image 20
Contents GZ400 Contents Advertencias Contenidas EN EL Manual Differents Types D’AVERTISSEMENT DE CE Mode D’EMPLOITables des matieres Contenido GZ400 SpecificationsParts location Emplacement des pieces Situación de las piezas Fiche techniqueRead operators instruction book before Operating this machineWear head, eye and ear protection Use the chain saw with two handsEtiquettes d’avertissement sur la machine Symbols on the machine Position Fuel capPosition Oil cap Emission ControlSymboles utilises sur la machine Control DE EmisionesFor safe operation Consignes de securite Instrucciones de seguridad For safe operation Consignes de securite Instrucciones de seguridad Kickback Safety Precautions for Chain SAW Users Consignes de securite Instrucciones de seguridad For safe operation Consignes de securite Instrucciones de seguridad Installing guide bar and saw chain SAFE-T-TIP nose guard F6-2 F6-3Mounting screw SAFE-T-TIP Tighten 3/4 of a TurnVis de montage Dispositif SAFE-T-TIP Serrez D’UN 3/4 DE TourTornillo de montaje Dispositivo protector SAFE-T-TIP Gire LA Llave 3/4 Para ApretarLoosen Tighten Tensioner screw Lift up Tensioner nut Chain coverMoving Direction Ecrou de tendeur Carter de chaîne Tuerca del tensor Cubierta de la cadenaSens de rotation Dirección del movimiento Desserrer Serrer Vis du tendeur SouleverRecommended Mixing Ratio Gasoline 50OIL When using RedMax/ZENOAH genuine oilFuel and chain oil Rapport DE Melange Recommande Essence 50 Huile Lors de l’utilisation de la véritable huile RedMax/ZENOAHProporción DE LA Mezcla Recomendada Gasolina 50 Aceite Al utilizar el aceite auténtico de RedMax/ZENOAHHOW to MIX Fuel Fueling the UnitAbastecimiento DE LA Unidad Comment Obtenir UN BON Melange Como Mezclar EL CombustibleRemplissage DU Reservoir For Your Engine LIFE, Avoid BAR & Chain OILEviter Pour Prolonger LA Duree DE VIE DU Moteur Para Contribuir a LA Vida Útil DEL MOTOR, EviteChain oil Fuel Switch OperationStarting the Engine PrimerArranque Estrangulador CompletoChain oil Adjusting the CarburetorChecking the OIL Supply Huile de chaîne Aceite para la cadenaRégLAGE DU Carburateur Ajuste DEL CarburadorChain Brake Fine adjustment of the idling speed T F8-7How to confirm Frein DE LA Chaîne Freno DE LA CadenaStopping the Engine Carburetor anti-freeze mechanismArrêt DU Moteur InterrupteurMécanisme antigel de carburateur Apagado DEL MotorChoke knob Cylinder cover Icing cap HOW to Switch Between OperatingModes F8-12 Cómo Cambiar DE Modo DE Operación F8-12 Fonctionnement UsoComment Changer Entre LES Modes D’UTILISATION F8-12 Sawing Guard Against Kickback F9-1Mesures DE Protection Contre LES Rebonds F9-1 Protección Contra Contragolpe F9-1Felling a Tree F9-2 Trozado y corte de ramas Abattage d’un arbre F9-2Talado DE Árboles F9-2 Cutting Limb of Fallen Tree F9-5 Log lying on the ground F9-3Log hanging off the ground F9-4 Tronc reposant sur le sol F9-3 Tronc en surélévation F9-4Ebranchage d’un arbre abattu F9-5 Elagage d’un arbre F9-6SAFE-T-TIP MaintenanceMaintenance After Each USE Entretien Apres Chaque Utilisation Mantenimiento Después DE Cada USOPeriodical Service Points Entretien Periodique Puntos DE Servicio PeríodicoFuel filter Spark plugNGK CMR7H SprocketFiltre à essence Filtro de combustibleFiltre à essence Filtro de combustible BougieMaintenance of Saw Chain and Guide Bar SAFE-T-TIP nose guard F11-1 F11-2Entretien de la chaîne et du guide-chaîne SAW Chain Entretien de la chaîne et du guide-chaîne Ruler Gap No gap Chain tilts Cutter length Filing angle Side plate angleGuide BAR Regla Separación Sin separación Cadena inclinada GUIDE-CHAÎNEBarra Guía Case 3. Oil does not come out Troubleshooting GuideCase 2. Lack of power/Poor acceleration/ Rough Idling Guide de dépannage 12. Guía para la localización de averíasCas 1. Défaut de démarrage Caso 1. Falla de arranqueStorage DisposalRangement Mise au rebutGZ400 NotaParts list Cylinder Assy Parts list Coil Assy Warranty 66%28= Garantie +%6%28 Garantía +%6%28Ú% Limited Warranty Garantie limitée Garantía Limitada