BRIGGSandSTRATTON.COM | Briggs & Stratton 10000 Watt manual

•Install the flexible, gaseous hose (supplied) between the home generator Fuel Inlet port and rigid piping to prevent thermal expansion or contraction from causing excessive stress on the piping material.

NOTE: Where local conditions include earthquake, tornado, unstable ground, or flood hazards, special consideration shall be given to increase strength and flexibility of piping supports and connections.

caution

The supplied flexible gaseous pipe is not to be installed underground or in contact with the ground.

•The entire flexible gaseous pipe must be visible for periodic inspection and must not be concealed within, contact, or run through any wall, floor, or partition.

•Piping must be of the correct size to maintain the required supply pressures and volume flow under varying generator load conditions with all gas appliances connected to the fuel system turned on and operating.

•Use an approved pipe sealant or joint compound on all threaded fittings to reduce the possibility of leakage.

•Installed piping must be properly purged and leak tested, in accordance with applicable codes and standards.

warning

Propane and Natural Gas are extremely flammable and explosive.

Fire or explosion can cause severe burns or death.

•Before placing the home generator into service, the fuel system lines must be properly purged and leak tested.

•No leakage is permitted.

Consider the following factors when planning to install the fuel supply system:

The home generator engine is fitted with a fuel mixer system that meets the specifications of the California Air Resources Board for “tamper-proof” fuel systems.

•A minimum of one accessible, approved manual shutoff valve shall be installed in the fuel supply line within

6 ft (1.8 m) of the home generator. A union or flanged connection shall be provided downstream from this valve to permit removal of controls.

•Natural gas fuel supply pressure at the generator’s fuel inlet port should be between 5 to 7 inches of water (in. W.C.) at full load.

•LP gas fuel supply pressure should be 11 to 14 inches of water (in. W.C.) at full load with all gas appliances turned on and operating.

The Home Generator has been factory set to run on natural gas. If you need to change from natural gas to LP gas, the unit will need to be reconfigured, as described in Fuel System Selection.

It is recommended that the fuel connection incorporate the following components:

•A manual fuel shut-off valve located in the interior of the building.

•A manual fuel shut-off valve located outside the building, just before the generator unit.

•Where the formation of hydrates or ice is known to occur, piping should be protected against freezing. The termination of hard piping should include a sediment trap where condensate is not likely to freeze.

•A manometer port should be provided.

The manometer port permits temporary installation of a manometer to ensure that the engine receives the correct fuel pressure to operate efficiently throughout its operating range.

NOTE: A digital manometer, P/N 19495, is available at your local Briggs & Stratton service center.

When the initial test runs are completed, the manometer is removed and the port is plugged. A typical final fuel connection assembly is shown here, where (A) is the fuel supply and (B) goes to the home generator.

10	BRIGGSandSTRATTON.COM

10000 Watt specifications

Briggs & Stratton has long been synonymous with quality engines and power products, and their 10,000-watt generator continues to uphold that reputation. This robust generator is designed for both home and professional use, making it suitable for emergency backups and job site applications alike. Its impressive power output is one of its standout features, providing ample electricity to run essential appliances, tools, and electronics during outages or in remote locations.

One of the primary features of the Briggs & Stratton 10,000-watt generator is its durable engine. The generator is equipped with a powerful 420cc OHV engine, which is designed for reliable performance under heavy loads. This engine is built to last, thanks to its rugged construction and reliable cooling system, ensuring optimal performance even during extended operating periods.

An essential characteristic of this generator is its impressive runtime. With a 7-gallon fuel tank, it can run for up to 9 hours at a 50% load, providing an extended period of power without the need for constant refueling. The inclusion of a fuel gauge allows users to check the fuel level easily, ensuring that they remain informed about fuel availability during usage.

The generator comes with an array of outlets, including multiple 120V household outlets, a 120/240V twist-lock outlet, and a USB port, enabling users to connect various devices simultaneously. This range of output options provides versatility for users who may need to power multiple appliances at once, whether it be during a blackout or at a job site.

In terms of technology, the Briggs & Stratton 10,000-watt generator features a self-diagnostic tool that monitors its performance and alerts the user to any potential issues before they become significant problems. This proactive approach to maintenance helps ensure that the generator remains in peak operating condition.

Another notable technology is the integrated idle control feature, which automatically adjusts the engine speed based on the load requirement. This not only improves fuel efficiency but also reduces noise levels, making it less obtrusive during use.

Additionally, the generator features a compact design with sturdy wheels for easy transport. Its durable frame is built to withstand rugged environments, while the folding handles make setup and storage convenient. Overall, the Briggs & Stratton 10,000-watt generator is an excellent choice for those seeking reliable power in various settings, combining strength, efficiency, and user-friendly features.