Final Installation Considerations

Engine Oil

notice

Any attempt to crank or start the engine before it has been properly serviced with the recommended oil will result in equipment failure.

•Refer to Maintenance and engine manual for oil fill information.

•Damage to equipment resulting from failure to follow this instruction will void engine and generator warranty.

This engine is shipped from the factory pre-run and filled with synthetic oil (API SJ/CF 5W-30W). This allows for system operation in the widest range of temperature and climate conditions. Before starting the engine, check oil level and ensure that engine is serviced as described in the engine operator’s manual.

NOTE: The use of synthetic oil does not alter the required oil change intervals described in the engine operator’s manual.

Battery

The installer must supply and install a 350 CCA (cold cranking amps), sealed, valve-regulated, lead-acid rechargeable 12 Volt DC, AGM type, starting battery.

NOTE: DO NOT use a deep-cycle or automotive type battery.

Install the battery as described in Servicing the Battery in the Maintenance section of the operator’s manual. Always make sure the negative cable is hooked up last.

The battery may not be at full charge when installed. If battery voltage is below 12 Volts, charge the battery. See Battery in Maintenance of the operator’s manual for details.

warning

Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling.

Fuel Supply System

Ensure that all fuel pipe connections are tight, secure and without leaks.

Ensure that all gas line shutoff valves are OPEN and that adequate fuel pressure is available whenever automatic operation is desired.

Fuel System Selection

The engine of your Home Generator System is factory calibrated to run on natural gas (NG). It may also be operated on liquefied petroleum (LP) vapor. There is no additional hardware/equipment required to switch between either fuel. However, LP fuel inlet pressure must be between 11 and 14 inches water column.

To configure the fuel system for LP use:

1.Remove control panel and oil fill access covers.

2.Set generator’s system switch to OFF.

3.Remove 15 Amp fuse from control panel.

4.Connect the fuel select solenoid by joining the two-pin electrical connector (A).

5. Reinstall 15 Amp fuse in control panel.

6.Set generator’s system switch to AUTO.

7.Install control panel and oil fill access covers.

The system is now ready to operate automatically using LP fuel. With a fixed main jet for LP gas, there is no need to perform any engine adjustments for LP operation.

Initial Start-up (No Load)

Before operating the home generator or placing it into service, inspect the entire installation carefully.

Then begin testing the system without any electrical loads connected, as follows:

1.Set generator’s main circuit breaker to its ON (closed) position.

2.Install 15 Amp fuse in control panel.

3.Set generator’s system switch to AUTO.

4.Push MANUAL OVER-RIDEbutton on control panel.

NOTE: When the home generator is started for the very first time, it will require that air in the gaseous fuel lines be purged. This may take a few minutes.

5.DO NOT crank engine for more than 10 seconds, then pause for 10 seconds to reduce heat in the starter.

6.Repeat process until engine starts.

7.Listen for unusual noises, vibration or other indications of abnormal operation. Check for oil leaks while engine runs.

8.Let engine warm up for about five minutes to allow internal temperatures to stabilize.

9.Connect an accurate AC voltmeter and a frequency meter to check generator output at load side of circuit breaker. Voltage should be 239‑262 Volts, frequency should be 62.0 - 62.5 Hz.

NOTE: If either parameter is outside these ranges, perform the Engine Adjustments described below.

10.Check generator output between one of the generator connection lugs and the neutral lug, then between the other generator connection lug and the neutral lug.

In both cases, voltage reading should be between 119‑131 Volts.

14	BRIGGSandSTRATTON.COM

10000 Watt specifications

Briggs & Stratton has long been synonymous with quality engines and power products, and their 10,000-watt generator continues to uphold that reputation. This robust generator is designed for both home and professional use, making it suitable for emergency backups and job site applications alike. Its impressive power output is one of its standout features, providing ample electricity to run essential appliances, tools, and electronics during outages or in remote locations.

One of the primary features of the Briggs & Stratton 10,000-watt generator is its durable engine. The generator is equipped with a powerful 420cc OHV engine, which is designed for reliable performance under heavy loads. This engine is built to last, thanks to its rugged construction and reliable cooling system, ensuring optimal performance even during extended operating periods.

An essential characteristic of this generator is its impressive runtime. With a 7-gallon fuel tank, it can run for up to 9 hours at a 50% load, providing an extended period of power without the need for constant refueling. The inclusion of a fuel gauge allows users to check the fuel level easily, ensuring that they remain informed about fuel availability during usage.

The generator comes with an array of outlets, including multiple 120V household outlets, a 120/240V twist-lock outlet, and a USB port, enabling users to connect various devices simultaneously. This range of output options provides versatility for users who may need to power multiple appliances at once, whether it be during a blackout or at a job site.

In terms of technology, the Briggs & Stratton 10,000-watt generator features a self-diagnostic tool that monitors its performance and alerts the user to any potential issues before they become significant problems. This proactive approach to maintenance helps ensure that the generator remains in peak operating condition.

Another notable technology is the integrated idle control feature, which automatically adjusts the engine speed based on the load requirement. This not only improves fuel efficiency but also reduces noise levels, making it less obtrusive during use.

Additionally, the generator features a compact design with sturdy wheels for easy transport. Its durable frame is built to withstand rugged environments, while the folding handles make setup and storage convenient. Overall, the Briggs & Stratton 10,000-watt generator is an excellent choice for those seeking reliable power in various settings, combining strength, efficiency, and user-friendly features.