Electrolux OHV Install Chute Deflector Remote Control See Figs, Install Weight BAG See Fig

Page 10

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

CONSUMER ASSEMBLY / PRE-OPERATION

INSTALL CHUTE DEFLECTOR REMOTE CONTROL (See Figs. 9 and 10)

1.Install remote cable bracket to discharge chute with 5/16-18 carriage bolt, flat washer and 5/16-18 locknut as shown. Tighten securely.

2.Install remote cable eyelet to chute deflector with 1/4-20 shoulder bolt, nylon washer and 1/4-20 locknut as shown. Tighten securely.

3.Install spring hooks between hex nuts on chute rotater head and into hole in chute deflector as shown.

CHUTE DE-	SPRING	1/4-20
FLECTOR		SHOULDER
NYLON		BOLT
NYLON
WASHER	HOOK BETWEEN
	HOOK BETWEEN
CABLE EYE-		HEX NUTS
LET	ON CHUTE RO-
1/4-20		TATER HEAD
1/4-20
LOCK-
NUT		5/16-18
		CARRIAGE
		BOLT
REMOTE
CABLE
BRACKET
FLAT
WASHER
5/16-18 LOCK-
NUT
	FIG. 9

CHUTE DEFLECTOR

CONTROL LEVER

FIG. 10

INSTALL WEIGHT BAG (See Fig. 11)

Though seldom required, the weight bag will reduce the tendency of the auger housing to ride up on hard, icy drifts. Should conditions require it, install as follows:

1.Shut off engine and wait for all moving parts to stop.

2.Fill weight bag with desired amount of sand.

3.Place weight bag on top of auger housing with mount- ing clamp at front edge of auger housing as shown.

IMPORTANT: Mount the weight bag in a location which does not cover the warning decals on top of the auger housing.

CHECK TIRE PRESSURE

MOUNTING	BAR
CLAMP
WEIGHT
BAG
5/16-18 x 1-1/2
CAPSCREWS
AUGER HOUSING
FIG. 11

The tires on your snow thrower were overinflated at the fac- tory for shipping purposes. Correct and equal tire pressure is important for best snow throwing performance.

•Reduce tire pressure to 14-17 PSI.

10

www.mymowerparts.com

Image 10

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Remove Snow Thrower from Carton Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigADD Gasoline See Fig Before Starting the EngineCheck Engine OIL Level See Fig To Start EngineBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Before Each USE Consumer MaintenanceGeneral Recommendations LubricationCleaning EngineTo Adjust Snow Thrower Height Consumer Service and AdjustmentsChute Deflector To Remove Wheels See Fig Engine OIL OtherCarburetor CylinderTroubleshooting Clearance Auger Belt Belt Guide16 to 1/8 Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeNUT and Bolt Speed Control Assembly Adjustment2nd Reverse Position Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Interlock Spring Check Wear Here Traction Auger Engagement Lever ScrewsConsole Lock TAB Into Hole Backside View Section Deflector Cable Assembly Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Chute Rotator Control Lever ScrewsNUT Washer Speed Control AssemblyRetainer Springs PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Right Bolt Left Bolt Belt Cover Right ScrewIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringFrame Slot For Drive Plate Drive Spring Barrel Connector Wood SupportHousing Screw Belt Guide Drive BeltSnow Thrower Section Drive Screws Flange Bearing HEX Head ScrewsNUT HEX Shaft Flange Bearing Pinion Gear Long HEX ShaftNuts Drive Plate Assembly ScrewsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY