Electrolux OHV service manual To Reinstall, Cable Assembly Locknut

Page 43

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.51Remove Chute Assembly for servicing other items

7.61Remove Auger Assembly for servicing

SPRING

NUT AND

WASHER

DEFLECTOR

CABLE

1) Remove spring that attaches from the deflector to the pivot.

NOTE: If unit is not equipped with a remote deflector proceed to step 4

2)Remove the nut and washer that secures the deflector cable to the deflector.

3)Remove the nut, washer and bracket that secure the cable to the chute.

CABLE

ASSEMBLY

9/16" LOCKNUT

1)Remove spark plug wire from plug.

2)Remove Deflector Chute (Section 7.51 Chute Removal)

3)Remove both 3/8" screws that secure belt cover. Remove belt cover.

RIGHT SCREW

4)Place a chair or saw horse behind handle assembly for support after auger section is split.

RIGHT BOLT

LEFT BOLT

5)Remove both 9/16" hex bolts that hold the powerhead and auger housing together.

4)Remove the 9/16" locknut and separate the cable assembly from the chute assembly.

The chute assembly will separate, be careful not to drop the chute onto the snowthrower.

5)Reverse process to reinstall chute deflector.

To Reinstall:

7)Place belt on auger pulley and use to lift auger assembly into position so that slotted bracket on auger housing are placed onto the rod at base of powerhead.

9) Route auger belt around pulleys/guide. Check that belt is not caught on idler brkt.

10)Reinstall bolts to secure auger housing to the powerhead and belt cover.

4311)Reinstall the chute assembly and plug wire.

www.mymowerparts.com

Image 43

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training PreparationOperation Maintenance and StorageSpecifications Consumer Assembly Parts Packed Separately in Carton Unfold Upper Handle Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonSee Fig Install Auger Control ROD See FigsInstall Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower Consumer OperationRecoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Throw Snow See FigTo Start Engine Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Lubrication Consumer MaintenanceGeneral Recommendations Before Each USEEngine CleaningTo Adjust Snow Thrower Height Consumer Service and AdjustmentsChute Deflector To Remove Wheels See Fig Cylinder OtherCarburetor Engine OILTroubleshooting Traction Belt Idler Spring Belt Guide16 to 1/8 Clearance Auger BeltProtective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control RodBellcrank Shifter Retainer Spring Control ROD Lever Speed Control Assembly Adjustment2nd Reverse Position NUT and BoltFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Interlock Spring Check Wear Here Traction Auger Engagement Lever ScrewsConsole Lock TAB Into Hole Backside View Section Chute Rotator Control Lever Screws Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Deflector Cable AssemblyPIN Speed Control AssemblyRetainer Springs NUT WasherSnow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering ClutchSnow Thrower Section Chassis / Engine / Pulleys Right Bolt Left Bolt Belt Cover Right ScrewIdler Pulley Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left WheelBelt Guide Drive Belt Barrel Connector Wood SupportHousing Screw Frame Slot For Drive Plate Drive SpringSnow Thrower Section Drive Flange Bearing Pinion Gear Long HEX Shaft HEX Head ScrewsNUT HEX Shaft Screws Flange BearingNuts Drive Plate Assembly ScrewsFrame Slot Lubricate HEX Shaft Axle Bearing Screws InstructionCable Assembly Locknut To ReinstallSnow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear BoltsImpeller Shaft For Husqvarna Parts Call 606-678-9623 orTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE EngineService Notes Part Number 184962 printed for MY