Electrolux OHV Chute Rotator Control Lever Screws, Spring Cable Assembly Rotator Head

Page 31

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

Section 7.16: Replace Chute Rotator Cable

Section 7.17: Replace Chute Deflector Control

1)Remove control panel (see section 7.11 above, for Control Panel removal instructions)

CHUTE ROTATOR

CONTROL LEVER

SCREWS

2)Remove both 5/16" screws holding rotator control to handle assembly.

SPRING

CABLE ASSEMBLY

ROTATOR HEAD

9/16" NUT

CABLE ASSEMBLY

ROTATOR HEAD

3)Remove spring from deflector, if applicable.

4)Remove 9/16" nut holding control rotator head to tubular support, and remove cable assembly from the chute. The chute will not be retained at the top, DO NOT drop chute.

5)Cut all cable ties noting locations, and paying attention to the routing of cable particularly at the lower handle.

6)Reverse process to install new cable. Install new plastic ties to hold cables.

1) Remove control panel (see section 7.11).

SPRING

NUT AND

WASHER

DEFLECTOR

CABLE

2)Remove the nut and washer that secure the cable eyelet to the deflector.

3)Remove the nut, washer and bracket that secure cable to the chute.

DEFLECTOR

CONTROL

LEVER

SCREWS

DEFLECTOR

CABLE

ASSEMBLY

4)Remove both 5/16" screws that secure cable assembly to the handle assembly.

5)Cut the cable ties that secure the cable to the snowthrower, paying attention to the routing of the cable and the location of ties.

6)Reverse process to install the cable and new plastic ties.

31

www.mymowerparts.com

Image 31

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training PreparationOperation Maintenance and StorageSpecifications Consumer Assembly Parts Packed Separately in Carton Unfold Upper Handle Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonSee Fig Install Auger Control ROD See FigsInstall Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Know Your Snow Thrower Consumer OperationRecoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Throw Snow See FigTo Start Engine Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Lubrication Consumer MaintenanceGeneral Recommendations Before Each USEEngine CleaningTo Adjust Snow Thrower Height Consumer Service and AdjustmentsChute Deflector To Remove Wheels See Fig Cylinder OtherCarburetor Engine OILTroubleshooting Traction Belt Idler Spring Belt Guide16 to 1/8 Clearance Auger BeltProtective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control RodBellcrank Shifter Retainer Spring Control ROD Lever Speed Control Assembly Adjustment2nd Reverse Position NUT and BoltFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Interlock Spring Check Wear Here Traction Auger Engagement Lever ScrewsConsole Lock TAB Into Hole Backside View Section Chute Rotator Control Lever Screws Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Deflector Cable AssemblyPIN Speed Control AssemblyRetainer Springs NUT WasherSnow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering ClutchSnow Thrower Section Chassis / Engine / Pulleys Right Bolt Left Bolt Belt Cover Right ScrewIdler Pulley Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left WheelBelt Guide Drive Belt Barrel Connector Wood SupportHousing Screw Frame Slot For Drive Plate Drive SpringSnow Thrower Section Drive Flange Bearing Pinion Gear Long HEX Shaft HEX Head ScrewsNUT HEX Shaft Screws Flange BearingNuts Drive Plate Assembly ScrewsFrame Slot Lubricate HEX Shaft Axle Bearing Screws InstructionCable Assembly Locknut To ReinstallSnow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear BoltsImpeller Shaft For Husqvarna Parts Call 606-678-9623 orTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE EngineService Notes Part Number 184962 printed for MY