Electrolux OHV service manual Meets A.N.S.I. Safety Requirements

Page 12

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

CONSUMER OPERATION

	SPARK	ENGINE OIL CAP	AUGER CON-	DISCHARGE CHUTE CONTROL LEVER
	PLUG	WITH DIPSTICK	TROL LEVER
	SAFETY		DRIVE SPEED CON-		DEFLECTOR REMOTE CON-
	IGNITION		DRIVE SPEED CON-		DEFLECTOR REMOTE CON-
	IGNITION		TROL LEVER		TROL LEVER
	KEY	GASOLINE	TROL LEVER		TROL LEVER
	KEY

		FILLER
		CAP			TRACTION
	CHOKE		CHUTE DE-		TRACTION
			CHUTE DE-		DRIVE CON-
			FLECTOR		DRIVE CON-
	CON-		FLECTOR		TROL LEVER
	CON-				TROL LEVER
	TROL

THROTTLE /			LH TURN
ENGINE CON-			TRIGGER
TROL
		OIL DRAIN
		PLUG	LIGHT
RECOIL (AUXIL-	POWER
IARY) STARTER	POWER
IARY) STARTER	CORD
HANDLE	CORD
HANDLE	PLUG	ELECTRIC
	PLUG

		START BUT- FUEL SHUT-OFF VALVE	HANDLE
		TON	KNOB
		DISCHARGE	KNOB
PRIMER		DISCHARGE
		CHUTE
			MUFFLER
NOTE: ITEMS
ABOVE ARE SHOWN
IN THEIR TYPICAL			TOOLBOX
LOCATION ON THE
ENGINE. ACTUAL
LOCATION MAY
VARY WITH THE
ENGINE ON YOUR
UNIT.

AUGER

SKID PLATE

FIG. 12

MEETS A.N.S.I. SAFETY REQUIREMENTS

Our snow throwers conform to the standards of the American National Standards Institute.

Toolbox - used to store spare shear bolts, locknuts and wrench.

Safety ignition key - must be inserted for the engine to start and run. Remove when snow thrower is not in use.

Electric start button - used for starting the engine.

Recoil (auxiliary) starter handle - used for starting the en-

gine.

Primer - pumps additional fuel from the carburetor to the cylinder for use when starting a cold engine.

Choke Control - used for starting a cold engine.

Throttle/engine control - used to select either FAST or SLOW engine speed and to STOP the engine.

LH and RH turn triggers - used to steer the snow thrower.

Drive speed control lever - used to select forward or reverse motion and speed of snow thrower.

Traction drive control lever - used to engage power-propelled forward or reverse motion of snow thrower.

Auger control lever - used to engage auger motion (throw snow).

Discharge chute control lever - used to change the direction

the snow is thrown.

Deflector remote control lever - used to change the distance

the snow is thrown.

Skid plate - used to adjust height of scraper bar from the

12ground.

www.mymowerparts.com

Image 12

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Consumer Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Chute Deflector Remote Control See Figs Install Weight BAG See FigCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline See Fig To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Consumer Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineConsumer Service and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Other CarburetorEngine OIL CylinderTroubleshooting Belt Guide 16 to 1/8Clearance Auger Belt Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeSpeed Control Assembly Adjustment 2nd Reverse PositionNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Traction Auger Engagement Lever Screws Interlock Spring Check Wear HereConsole Lock TAB Into Hole Backside View Section Spring Cable Assembly Rotator Head Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsSpeed Control Assembly Retainer SpringsNUT Washer PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Belt Cover Right Screw Right Bolt Left BoltIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringBarrel Connector Wood Support Housing ScrewFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive HEX Head Screws NUT HEX ShaftScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftDrive Plate Assembly Screws NutsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY