Electrolux OHV service manual Adjustment for Drive System Control Rod

Page 24

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

6.21Adjustment for Drive System Control

Rod

* The Drive System Control Rod is on the han- dle at the left side of the operator. Adjustment is required if engagement is sluggish or if there is creep.

* Loosen the jam nut, remove hairpin, and dis- connect control rod from control lever. Turn the rod counter-clock-wise to lengthen, clock-wise to shorten. Reconnect the control rod lever.

Slack should be removed and the rod should be snug. If not, readjust. Then tighten jam nut. * If this adjustment is not successful, use anti- seize to lubricate the Hex Short Shaft (page 39 key 28) on the Drive Plate Assembly (key 26). See Section 7.45 for disassembly information .

PROTECTIVE

SLEEVE

JAM NUT

CONTROL

ROD

FEELER GAUGE

6.22 Adjustment for worn traction disc ring * Remove spark plug wire when making adjust- ments.

* Position snowthrower with auger down and remove Bottom Pan to inspect disc.

(see Section 7.42)

24

*If the rubber ring on the traction disc is missing chunks, has deep cracks, or is worn so the rubber ring clamp plates are 1/16" or less from touching the drive plate in engaged position, the rubber ring must be replaced.

*If the rubber ring passes inspection, in the disengaged position adjust the clearance be- tween the Rubber Wheel Ring and the Drive Plate Assembly to .125"-.140".

*If there is a complaint that the drive does

not disengage properly, check to see that this dimension is at least .125".

*To adjust clearance, use 9/16" nut connecting the bellcrank to a clutch rod. It is at bottom end of the Drive Control Rod (p 35 key 36). When a new rubber ring is installed, this nut is adjusted so that two threads are showing past the nut.

When the ring is worn, it can be adjusted with up to 1/2" of rod past the nut. This increases the force of the drive plate on the rubber ring to stop slipping. The nut should never be turned so that more than 1/2" extends beyond the nut.

( See Section 7.43 )

NOTE: If the Plates supporting the Rubber Wheel Ring come in contact with the Drive Plate Assembly (p 39 Key 26) extreme wear may require that these parts be replaced.

www.mymowerparts.com

Image 24

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Consumer Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Chute Deflector Remote Control See Figs Install Weight BAG See FigCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline See Fig To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Consumer Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineConsumer Service and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Other CarburetorEngine OIL CylinderTroubleshooting Belt Guide 16 to 1/8Clearance Auger Belt Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeSpeed Control Assembly Adjustment 2nd Reverse PositionNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Traction Auger Engagement Lever Screws Interlock Spring Check Wear HereConsole Lock TAB Into Hole Backside View Section Spring Cable Assembly Rotator Head Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsSpeed Control Assembly Retainer SpringsNUT Washer PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Belt Cover Right Screw Right Bolt Left BoltIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringBarrel Connector Wood Support Housing ScrewFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive HEX Head Screws NUT HEX ShaftScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftDrive Plate Assembly Screws NutsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY