Electrolux OHV service manual Retainer Springs, Speed Control Assembly, NUT Washer, Pin

Page 32

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

Section 7.18: Replace Speed Control Linkage or Speed Control Assembly

1)Check for proper linkage adjustment in Section 6.24 before replacing part.

2)Remove control panel (see section 7.11 )

RETAINER

SPRINGS

3)Remove retainer spring from both ends of linkage.

SCREWS

SPEED CONTROL

ASSEMBLY

4)Remove the two 5/16" hex head screws holding control to handle assembly.

5)Reverse process to install a new linkage and perform adjustment in Section 6.24.

Section 7.19: Remove and Replace Power Steering Control Cable

1)Remove fuel from fuel tank

2)Position blower auger end down.

3)Remove klik pin that secures wheel,

4)Remove wheel POWER STEERING COVER

5/16" SCREWS

NUT &

WASHER

5)Remove hardware that secures the power steering cover.

6)Cut wire ties that secure power steering cable to handle, noting location of ties.

BELLCRANK

PIN

7)Remove spring and pin holding bellcrank.

8)Unhook cable from bellcrank. Remove 5/16" screw that secures trigger to handle. Remove cable.

5/6" HEX HEAD SCREW

TURN TRIGGER

CABLE

9)Remove 5/16" screw that secures trigger to handle.

10)Reverse process to install cable.

32

www.mymowerparts.com

Image 32

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Consumer Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs See FigCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAG See Fig Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline See Fig To Start EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Consumer Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineChute Deflector Consumer Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Other CarburetorEngine OIL CylinderTroubleshooting Belt Guide 16 to 1/8Clearance Auger Belt Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeSpeed Control Assembly Adjustment 2nd Reverse PositionNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Console Lock TAB Into Hole Backside View Traction Auger Engagement Lever ScrewsInterlock Spring Check Wear Here Section Spring Cable Assembly Rotator Head Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsSpeed Control Assembly Retainer SpringsNUT Washer PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Idler Pulley Belt Cover Right ScrewRight Bolt Left Bolt Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringBarrel Connector Wood Support Housing ScrewFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive HEX Head Screws NUT HEX ShaftScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftFrame Slot Drive Plate Assembly ScrewsNuts Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY