Electrolux OHV Repair Power Steering Clutch, Cable Spring PIN Bellcrank Link Retainer

Page 34

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.22 Repair Power Steering Clutch

When reassembled, the splined parts must be lubricated with metallic anti-seize compound.

CABLE

SPRING

PIN

BELLCRANK
LINK		RETAINER
LINK

		SPRING
		SPRING

7.23 If Power Steering Slips -

7.24Power Steering uses Klik Pin in one position only

7.25Standard Drive uses Klik Pin in Drive and Push positions

1)To freewheel, for models without power steering, remove klik pin from axle.

Go to 6.31for procedure to add shim washer if power steering slips on one side.

2)Push wheel hub in towards the body of the blower

34

www.mymowerparts.com

Image 34

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Remove Snow Thrower from Carton Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigADD Gasoline See Fig Before Starting the EngineCheck Engine OIL Level See Fig To Start EngineBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Before Each USE Consumer MaintenanceGeneral Recommendations LubricationCleaning EngineTo Adjust Snow Thrower Height Consumer Service and AdjustmentsChute Deflector To Remove Wheels See Fig Engine OIL OtherCarburetor CylinderTroubleshooting Clearance Auger Belt Belt Guide16 to 1/8 Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeNUT and Bolt Speed Control Assembly Adjustment2nd Reverse Position Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Interlock Spring Check Wear Here Traction Auger Engagement Lever ScrewsConsole Lock TAB Into Hole Backside View Section Deflector Cable Assembly Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Chute Rotator Control Lever ScrewsNUT Washer Speed Control AssemblyRetainer Springs PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Right Bolt Left Bolt Belt Cover Right ScrewIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringFrame Slot For Drive Plate Drive Spring Barrel Connector Wood SupportHousing Screw Belt Guide Drive BeltSnow Thrower Section Drive Screws Flange Bearing HEX Head ScrewsNUT HEX Shaft Flange Bearing Pinion Gear Long HEX ShaftNuts Drive Plate Assembly ScrewsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY