Electrolux OHV service manual Instruction, Lubricate HEX Shaft Axle Bearing Screws

Page 42

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.46Disassemble Drive Plate / Drive Pulley Assembly (Shaft Lubrication

INSTRUCTION )

7.47 Replace Wheel Drive Axle / Gear

1)Remove Frame Bottom Pan. Section 7.42.

2)Remove covers and disassemble power steering on both sides if so equipped.

SPRING	PIVOT PIN
	HAIRPIN RETAINER
	SHIFT PLATE LEVER
	CLUTCH ROD

1)Unhook Spring from Clutch Rod (key 11)

2)Remove Hairpin Retainer (key 22) from the Shift Plate Lever.

3)Remove Pivot Pin and separate Drive Plate (key 26) from hex shaft.

LUBRICATE HEX SHAFT

AXLE BEARING SCREWS

4)Inspect parts for wear and replace if necessary.

5)Lubricate all sides of Hex Shaft with metallic anti-seize compound.

6)Reverse the order to reassemble.

NOTE: Lubrication of the Hex Shaft with metallic antiseize compound is recommended every 120 hours of operation. If this assembly is removed, we recommend the hex shaft is lubricated with anti-seize compound.

3)Remove the screws on the right side that secure axle bushing to the frame.

4)Slide the axle out the right side and replace damaged parts.

5)Reverse process to reassemble. Make sure the square key, roll pin, and thrust washer is located between gear and bearing

42

www.mymowerparts.com

Image 42

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Remove Snow Thrower from Carton Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Chute Deflector Remote Control See Figs Install Weight BAG See FigCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigADD Gasoline See Fig Before Starting the EngineCheck Engine OIL Level See Fig To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Before Each USE Consumer MaintenanceGeneral Recommendations LubricationCleaning EngineConsumer Service and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Engine OIL OtherCarburetor CylinderTroubleshooting Clearance Auger Belt Belt Guide16 to 1/8 Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeNUT and Bolt Speed Control Assembly Adjustment2nd Reverse Position Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Traction Auger Engagement Lever Screws Interlock Spring Check Wear HereConsole Lock TAB Into Hole Backside View Section Deflector Cable Assembly Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Chute Rotator Control Lever ScrewsNUT Washer Speed Control AssemblyRetainer Springs PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Belt Cover Right Screw Right Bolt Left BoltIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringFrame Slot For Drive Plate Drive Spring Barrel Connector Wood SupportHousing Screw Belt Guide Drive BeltSnow Thrower Section Drive Screws Flange Bearing HEX Head ScrewsNUT HEX Shaft Flange Bearing Pinion Gear Long HEX ShaftDrive Plate Assembly Screws NutsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY