Electrolux OHV service manual For Husqvarna Parts Call 606-678-9623 or, Impeller Shaft

Page 46

3) With auger housing sitting on its back insert gearbox / auger / impeller as an assembly into place.

4) Reinstall screws to side of housing to secure the auger bearings.

7.66 Reassembly of Auger Assembly NOTE: Before re-assembling, clean impeller shaft where the auger pulley will be installed using emery cloth, and lubricate shaft end with

anti-seize.RIGHT SIDE

AUGER

AUGER BEARING

1) Place auger bearings at ends of auger with center notch in bearing toward housing ends.

LEFT SIDE AUGER

30" AUGER WIDTH

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

IMPELLER SHAFT

5) Turn Auger assembly over, put antiseize compound on impeller shaft before installing pulley. Torque at 15-20 Ft.Lbs.

6) Reinstall belt and reattach auger assembly to powerhead. (Section 7.61 or 7.31).

7.67 Replace Scraper Bar

NOTE: The Scraper Bar is reversible. Inspect Scraper Bar on snowthrower before ordering a replacement.

2) Check the end of the auger flight. Stamped into the metal is an “L” on the left side or “R”

on the right as well as the auger width.

CARRIAGE BOLTS

SCRAPER BAR

AND NUTS

1) Tip snowthrower so that Auger is down and handles are up.

2) Remove the nuts and carriage bolts holding the scraper to the housing.

3) The scraper bar is reversible and can be turned over and reinstalled once before replacement is required.

4) Reuse carriage bolts and nuts to install scraper bar.

7.68 Gearbox Repair Information

Replace worn or damaged parts. Replace gas- ket. Use 750369 grease. Torque self-tapping screw to 15 Ft.Lbs. max.

46

www.mymowerparts.com

Image 46

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Remove Snow Thrower from Carton Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigADD Gasoline See Fig Before Starting the EngineCheck Engine OIL Level See Fig To Start EngineBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Before Each USE Consumer MaintenanceGeneral Recommendations LubricationCleaning EngineTo Adjust Snow Thrower Height Consumer Service and AdjustmentsChute Deflector To Remove Wheels See Fig Engine OIL OtherCarburetor CylinderTroubleshooting Clearance Auger Belt Belt Guide16 to 1/8 Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeNUT and Bolt Speed Control Assembly Adjustment2nd Reverse Position Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Interlock Spring Check Wear Here Traction Auger Engagement Lever ScrewsConsole Lock TAB Into Hole Backside View Section Deflector Cable Assembly Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Chute Rotator Control Lever ScrewsNUT Washer Speed Control AssemblyRetainer Springs PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Right Bolt Left Bolt Belt Cover Right ScrewIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringFrame Slot For Drive Plate Drive Spring Barrel Connector Wood SupportHousing Screw Belt Guide Drive BeltSnow Thrower Section Drive Screws Flange Bearing HEX Head ScrewsNUT HEX Shaft Flange Bearing Pinion Gear Long HEX ShaftNuts Drive Plate Assembly ScrewsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY