Electrolux OHV service manual HEX Head Screws, NUT HEX Shaft, Screws Flange Bearing

Page 40

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.42 Remove Frame Bottom Pan

1)Remove fuel from fuel tank.

2)If repair involves removal of Drive Plate Assembly. See section 7.45.

3)Remove Belt cover. Use tape to hold end of Drive Belt Idler Spring in place, see page 37.

4)If the Drive Plate Assembly is to be removed, use a 3/8" drive ratchet with a 6" extension to remove tension from the traction drive belt by pulling up. Remove belt from engine pulley, see Section 7.34.

HEX HEAD

SCREWS

HEX HEAD

SCREWS

7.43Replace Rubber Wheel Ring or Hex Shaft

1)Remove wheels

2)Remove bottom pan (Section 7.42)

NUT

3/4" HEX SHAFT

3)Using a 3⁄4” wrench to hold the shaft , remove nut on right side

SCREWS

FLANGE

BEARING

4)Remove both screws that secure flange bearing on left side.

5)Position snowthrower so auger is down and handles are up.

6)Remove both wheels

7)Remove the four Hex Head Screws that hold the bottom pan to the frame.

8)Reverse to reassemble.

180017 FLANGE BEARING

180065 PINION GEAR

180066 LONG HEX SHAFT

5)Pull bearing/hex shaft assembly out from left side.

6)Remove Assembly with Rubber Wheel Ring from shifter fork and support Plates.

7)Replace Rubber Wheel Ring and torque bolts to 14-18 Ft.Lbs.

8)Reverse process to install. Lubricate hex shaft with metallic anti-seize before re- installing. Check to see that trunion bearing

round tabs are positioned in slots of shifter

40fork.

www.mymowerparts.com

Image 40

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Consumer Assembly / PRE-OPERATION HOW to SET UP Your Snow ThrowerRemove Snow Thrower from Carton Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Weight BAG See Fig Install Chute Deflector Remote Control See FigsCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingPower Steering Operation See Fig To Adjust Skid Plates See FigTo Throw Snow See Fig To Move Forward and Backward See FigBefore Starting the Engine Check Engine OIL Level See FigADD Gasoline See Fig To Start EngineBefore Stopping Snow Throwing TipsIf Recoil Starter has Frozen Consumer Maintenance General RecommendationsBefore Each USE LubricationCleaning EngineTo Adjust Snow Thrower Height Consumer Service and AdjustmentsChute Deflector To Remove Wheels See Fig Other CarburetorEngine OIL CylinderTroubleshooting Belt Guide 16 to 1/8Clearance Auger Belt Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeSpeed Control Assembly Adjustment 2nd Reverse PositionNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Interlock Spring Check Wear Here Traction Auger Engagement Lever ScrewsConsole Lock TAB Into Hole Backside View Section Spring Cable Assembly Rotator Head Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsSpeed Control Assembly Retainer SpringsNUT Washer PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Right Bolt Left Bolt Belt Cover Right ScrewIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringBarrel Connector Wood Support Housing ScrewFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive HEX Head Screws NUT HEX ShaftScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftNuts Drive Plate Assembly ScrewsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY