Electrolux OHV Belt Guide, 16 to 1/8, Clearance Auger Belt, Traction Belt Idler Spring

Page 23

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

SECTION 6: ADJUSTMENTS

6.01 Belt Guide

6.11Klik Pin Position for wheels on Power Steering Drive Snowthrower

6.12Klik Pin Positions for wheels on Standard Drive Snowthrower

6.21Adjustment for Drive System Control Rod

6.22Adjustment for worn Traction Disc Ring

6.23Adjustment for Auger Control Rod

6.24Adjustment for Speed Control Rod

6.31Procedure to add shim washer when Power Steering Slips

6.01 Belt Guide -

*Remove spark plug wire from plug.

*Engage auger lever and adjust clearance be- tween belt and belt guide to 1/16" to 1/8".

BELT GUIDE

1/16" to 1/8"

CLEARANCE

AUGER BELT

6.11Klik Pin Position for wheels on Power Steering Drive Snowthrower

6.12Klik Pin Positions for wheels on Stan- dard Drive Snowthrower

*To Push the snowthrower easily, the Klik Pin should be through the outer axle hole, with the wheel hub to the inside.

TRACTION BELT IDLER SPRING

*This is the only position for the Klik Pin where the Power Steering will work. The hole in the wheel hub is NEVER used with Power Steering.

*For the wheel to drive, the Klik Pin should be positioned through both the wheel hub and inner axle hole.

23

www.mymowerparts.com

Image 23
Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training PreparationOperation Maintenance and StorageSpecifications Consumer Assembly Parts Packed Separately in Carton Unfold Upper Handle Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Remove Snow Thrower from CartonSee Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAG See Fig Know Your Snow Thrower Consumer OperationRecoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Move Forward and Backward See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Throw Snow See FigTo Start Engine Before Starting the EngineCheck Engine OIL Level See Fig ADD Gasoline See FigIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Lubrication Consumer MaintenanceGeneral Recommendations Before Each USEEngine CleaningChute Deflector Consumer Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Cylinder OtherCarburetor Engine OILTroubleshooting Traction Belt Idler Spring Belt Guide16 to 1/8 Clearance Auger BeltProtective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control RodBellcrank Shifter Retainer Spring Control ROD Lever Speed Control Assembly Adjustment2nd Reverse Position NUT and BoltFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Console Lock TAB Into Hole Backside View Traction Auger Engagement Lever ScrewsInterlock Spring Check Wear Here Section Chute Rotator Control Lever Screws Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Deflector Cable AssemblyPIN Speed Control AssemblyRetainer Springs NUT WasherSnow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering ClutchSnow Thrower Section Chassis / Engine / Pulleys Idler Pulley Belt Cover Right ScrewRight Bolt Left Bolt Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left WheelBelt Guide Drive Belt Barrel Connector Wood SupportHousing Screw Frame Slot For Drive Plate Drive SpringSnow Thrower Section Drive Flange Bearing Pinion Gear Long HEX Shaft HEX Head ScrewsNUT HEX Shaft Screws Flange BearingFrame Slot Drive Plate Assembly ScrewsNuts Lubricate HEX Shaft Axle Bearing Screws InstructionCable Assembly Locknut To ReinstallSnow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear BoltsImpeller Shaft For Husqvarna Parts Call 606-678-9623 orTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE EngineService Notes Part Number 184962 printed for MY