Electrolux OHV Traction Auger Engagement Lever Screws, Interlock Spring Check Wear Here

Page 29

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

Section 7.11 Remove Console Panel to service controls and handles.

1)Remove the four 5/16" screws that hold panel to handle assembly. On re-assembly do not over tighten.

2)Remove all of the knobs and the Headlight ( See Section 7.13 below).

3)Carefully separate lock tab at each side and remove control panel from assembly.

4.) Reverse to reassemble. Check picture for position of tabs and stops on back side of Console Panel.

TRACTION	AUGER
ENGAGEMENT	ENGAGEMENT
LEVER	LEVER

SCREWS

Section 7.12 Auger Engagment Interlock

-When the auger and the traction engagement levers are engaged at the same time, you can remove your hand from the auger lever and the auger will remain engaged as long as the traction lever is also held down. This is to allow the operator to adjust the discharge chute direction without stopping. If problems occur with interlock, check the spring and look for wear on the bracket. You will see this on the right with the console panel removed.

INTERLOCK

SPRING

CHECK

WEAR

HERE

Section 7.13 Replace Headlight

*Use two fingers to push up on Headlight Bezel to release bottom tabs and remove Headlight.

*To remove harness connector, pull tabs on both sides outward while pulling connector from Headlight.

NOTE: Light is ‘on’ when engine is running. There is not a switch. See engine manufacturers

TABS	manual for information on charging system.

	STOPS
	CONSOLE	LOCK TAB INTO HOLE
	BACKSIDE VIEW	LOCK TAB INTO HOLE
	BACKSIDE VIEW

29

www.mymowerparts.com

Image 29

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training PreparationOperation Maintenance and StorageSpecifications Consumer Assembly Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Consumer Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleSee Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAG See Fig Know Your Snow Thrower Consumer OperationRecoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Adjust Skid Plates See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineADD Gasoline See Fig To Start EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations Consumer MaintenanceBefore Each USE LubricationEngine CleaningChute Deflector Consumer Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Carburetor OtherEngine OIL CylinderTroubleshooting 16 to 1/8 Belt GuideClearance Auger Belt Traction Belt Idler SpringProtective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control Rod2nd Reverse Position Speed Control Assembly AdjustmentNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Console Lock TAB Into Hole Backside View Traction Auger Engagement Lever ScrewsInterlock Spring Check Wear Here Section Cable Assembly Rotator Head Spring Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsRetainer Springs Speed Control AssemblyNUT Washer PINSnow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering ClutchSnow Thrower Section Chassis / Engine / Pulleys Idler Pulley Belt Cover Right ScrewRight Bolt Left Bolt Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left WheelHousing Screw Barrel Connector Wood SupportFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive NUT HEX Shaft HEX Head ScrewsScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftFrame Slot Drive Plate Assembly ScrewsNuts Lubricate HEX Shaft Axle Bearing Screws InstructionCable Assembly Locknut To ReinstallSnow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear BoltsImpeller Shaft For Husqvarna Parts Call 606-678-9623 orTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE EngineService Notes Part Number 184962 printed for MY