Electrolux OHV service manual Nuts, Frame Slot, Drive Plate Assembly Screws

Page 41

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.44 Replace Intermediate Gear

1)Remove bottom pan (Section 7.42).

2)Remove bolts holding lower handle to left side of frame.

NUTS

3)Remove four 1⁄2” nuts that secure the gear and the Auxiliary Plate.

4)Remove bolt through center of gear. NOTE: Inspect pinion on Hex Shaft, if damaged replace. Lubricate Hex Shaft.

5)Replace gear and reassemble reversing the process. Torque nuts at 4-6 Ft.Lbs. Lubricate center of gear with grease.

7.45 Replace Drive Plate Assembly

3)Remove the 1⁄2” nut holding the clutch rod to the drive control bellcrank.

FRAME SLOT

1)The Drive Belt must be removed from the Engine Pulley. (Section 7.32)

FRAME

BOTTOM

PAN

POWER

STEERING

COVER

DRIVE PLATE

ASSEMBLY

SCREWS

LOWER

FRONT

SCREW

2) If equipped with power steering, remove the

screw holding the power steering cover at
lower front on both sides.	41
	41

DRIVE PLATE

ASSEMBLY

SCREWS

4)Remove the 4 screws (2 each side) from the frame that hold the mounting drive plate in place. The zinc plated screws on left side are slightly longer.

5)Remove belt from pulley

6)Slide Drive Plate Assembly out.

NOTE: Whenever this assembly is removed, it is strongly suggested to lubricate the Hex Shaft with anti-seize compound. See Section 7.46 for instructions.

7)Place belt on pulley in correct position, be sure the clutch rod is through the hole in top left end of plate. Reverse the order to reassemble.

8)The top left corner of the Drive Plate Assembly will fit into Frame Slot.

9)Install 1⁄2” nut at bellcrank so two threads are showing on clutch rod. See Section 6.22.

www.mymowerparts.com

Image 41

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training PreparationOperation Maintenance and StorageSpecifications Consumer Assembly Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Consumer Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleSee Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAG See Fig Know Your Snow Thrower Consumer OperationRecoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Adjust Skid Plates See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineADD Gasoline See Fig To Start EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations Consumer MaintenanceBefore Each USE LubricationEngine CleaningChute Deflector Consumer Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Carburetor OtherEngine OIL CylinderTroubleshooting 16 to 1/8 Belt GuideClearance Auger Belt Traction Belt Idler SpringProtective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control Rod2nd Reverse Position Speed Control Assembly AdjustmentNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Console Lock TAB Into Hole Backside View Traction Auger Engagement Lever ScrewsInterlock Spring Check Wear Here Section Cable Assembly Rotator Head Spring Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsRetainer Springs Speed Control AssemblyNUT Washer PINSnow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering ClutchSnow Thrower Section Chassis / Engine / Pulleys Idler Pulley Belt Cover Right ScrewRight Bolt Left Bolt Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left WheelHousing Screw Barrel Connector Wood SupportFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive NUT HEX Shaft HEX Head ScrewsScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftFrame Slot Drive Plate Assembly ScrewsNuts Lubricate HEX Shaft Axle Bearing Screws InstructionCable Assembly Locknut To ReinstallSnow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear BoltsImpeller Shaft For Husqvarna Parts Call 606-678-9623 orTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE EngineService Notes Part Number 184962 printed for MY