Electrolux OHV service manual Specifications

Page 6

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

SECTION 2: SPECIFICATIONS

ENGINE:

TECUMSEH OHV

 

GASOLINE CAPACITY:

4.0 Quart

 

On 5 & 5.5 HP

 

3.5 Quart

 

TYPE

 

Unleaded Regular only

 

OIL TYPE:

SAE 30

(above 40 F)

(API-SF-SJ)

 

SAE 5W-30 or 10W30

( 0 to 40 F)

 

 

SAE 0W-30

(below 0 F)

OIL CAPACITY: . ( TECUMSEH 5 or 5.5 HP )

21 Ounces

 

OIL CAPACITY: . ( TECUMSEH 9 & 11 HP ) . . . .

26 Ounces

 

SPARK PLUG:

 

Champion RN4C for OHV models(Gap.030")

 

 

Champion RJ-19LM for ‘L’ Head (Gap: .030")

ENGINE SPEED:

( TECUMSEH 5 or 5.5 HP ) .

3400 plus or minus 150 RPM

 

ENGINE SPEED:

( TECUMSEH 9 & 11 HP )

3500 plus or minus 150 RPM

 

ALTERNATOR:

On models with headlight option

 

ELECTRIC STARTER:

 

Available on selected models of snowthrower

DRIVE SYSTEM:

Traction Disc System with Gears BRAKE:None

TRACTION BELT:

Part Number 179092 Cog-V-Belt (Use OEM part

 

 

only)

 

 

WHEELS:

 

13" or 16"

 

 

TIRE PRESSURE:

14 to 17 PSI in operation

 

SNOWTHROWER AUGER SYSTEM:

24", 27", or 30" Widths

 

AUGER BELT:

Part Number

183533 ( Use OEM part only )

GEARBOX:

 

Worm with Gear / No Maintenance Required

SCRAPER BAR:

 

Reversible / Replaceable

 

SKID PLATES:

 

Adjustable / Replaceable

 

FASTENERS THAT MUST BE TORQUED:

 

 

 

BOLTS HOLDING ENGINE TO CHASSIS:

25 to 30 Ft.Lb.

 

LOWER HANDLE BOLTS:

 

25 to 30 Ft.Lb.

 

SCREWS INTO AUGER BEARINGS:

5 to 8 Ft.Lb.

 

BOLTS HOLDING PULLEY FOR RUBBER RING:

 

14 to 18 Ft.Lb.

 

PIVOT BOLT FOR IDLER BRACKET (ON ENGINE): . . .

12 to 16 Ft.Lb.

 

BELT GUIDE BOLT ( ON ENGINE ):

 

12 to 16 Ft.Lb.

 

BOLT HOLDING AUGER TO POWERHEAD:

25 to 30 Ft.Lb.

 

SELF TAPPING SCREWS FOR FLANGE BEARING ASSY:

14 to 18 Ft.Lb.

 

METALLIC ANTI - SEIZE REQUIRED ON POWER STEERING SPLINE AND FRICTION PLATE SHAFT

6

www.mymowerparts.com

Page 5 Page 7
Image 6
Page 5 Page 7
Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Remove Snow Thrower from Carton Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Auger Control ROD See Figs See FigInstall Chute Deflector Remote Control See Figs Install Weight BAG See FigCheck Tire Pressure Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigADD Gasoline See Fig Before Starting the EngineCheck Engine OIL Level See Fig To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen Before Each USE Consumer MaintenanceGeneral Recommendations LubricationCleaning EngineConsumer Service and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Engine OIL OtherCarburetor CylinderTroubleshooting Clearance Auger Belt Belt Guide16 to 1/8 Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeNUT and Bolt Speed Control Assembly Adjustment2nd Reverse Position Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Traction Auger Engagement Lever Screws Interlock Spring Check Wear HereConsole Lock TAB Into Hole Backside View Section Deflector Cable Assembly Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Chute Rotator Control Lever ScrewsNUT Washer Speed Control AssemblyRetainer Springs PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Belt Cover Right Screw Right Bolt Left BoltIdler Pulley Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringFrame Slot For Drive Plate Drive Spring Barrel Connector Wood SupportHousing Screw Belt Guide Drive BeltSnow Thrower Section Drive Screws Flange Bearing HEX Head ScrewsNUT HEX Shaft Flange Bearing Pinion Gear Long HEX ShaftDrive Plate Assembly Screws NutsFrame Slot Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY
Top Page Image Contents