Electrolux OHV Frame Slot For Drive Plate Drive Spring, Belt Guide Drive Belt, Housing Screw

Page 38

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

7.37 Remove and replace engine.	7)	Remove Frame Bottom Pan (Section 7.42).
	8)	Remove Drive Plate Assy. (Section 7.43).

1)Remove belt cover ( Sections 7.31 & 7.32).

2)Remove both belts from engine pulleys. See page 20

FRAME SLOT

FOR

DRIVE PLATE

DRIVE SPRING

3)Tape idler Spring to outside of powerhead body. IDLER BRACKET ENGINE PULLEYS

BELT GUIDE

DRIVE BELT

4)Remove traction drive belt idler bracket, belt guide for auger drive, and engine pulleys.

BARREL

CONNECTOR

WOOD SUPPORT

9)Place a piece of wood (15" long by 3/4" thick) between Engine and Pivot Support.

10)Use a 1/2" socket with 15" extension to remove the 4 engine mounting bolts.

11)Remove engine.

12)Place new engine on side on pivot support for reinstallation. A board about 3/4" thick placed across pivot support will help to position engine while starting self-tapping screws. Torque screws holding engine to chassis at 25-30 Ft.Lbs.

13)Reinstall Drive Plate Assembly,

(Section 7.45)

14)Place wheels back on axles so the blower can be tipped back into operating position. Reinstall engine pulleys, idler bracket with idler pulley, belt guide, attach idler spring, and belts. Adjust Belt Guide as shown in Section 6.01.

HOUSING

SCREW

5)Disconnect headlight wire harness on engine.

6)Position Snowthrower with front of auger down.

NOTE: With Frame Bottom Pan off, the belts are accessible from the bottom for installation on pulleys. Do not install bottom Pan until belts are fully installed.

15)Reposition snow thrower with front of auger down. Reinstall frame bottom pan. Tip snowthrower back to operating position. Reinstall belt cover.

38

www.mymowerparts.com

Image 38

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Preparation TrainingMaintenance and Storage OperationSpecifications Consumer Assembly Parts Packed Separately in Carton Remove Snow Thrower from Carton Consumer Assembly / PRE-OPERATIONHOW to SET UP Your Snow Thrower Unfold Upper HandleInstall Auger Control ROD See Figs See FigCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAG See Fig Consumer Operation Know Your Snow ThrowerMeets A.N.S.I. Safety Requirements Recoil auxiliary starter handle used for starting the enHOW to USE Your Snow Thrower StoppingTo Throw Snow See Fig Power Steering Operation See FigTo Adjust Skid Plates See Fig To Move Forward and Backward See FigADD Gasoline See Fig Before Starting the EngineCheck Engine OIL Level See Fig To Start EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping Before Each USE Consumer MaintenanceGeneral Recommendations LubricationCleaning EngineChute Deflector Consumer Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Engine OIL OtherCarburetor CylinderTroubleshooting Clearance Auger Belt Belt Guide16 to 1/8 Traction Belt Idler SpringAdjustment for Drive System Control Rod Protective Sleeve JAM NUT Control ROD Feeler GaugeNUT and Bolt Speed Control Assembly Adjustment2nd Reverse Position Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Console Lock TAB Into Hole Backside View Traction Auger Engagement Lever ScrewsInterlock Spring Check Wear Here Section Deflector Cable Assembly Spring Cable Assembly Rotator HeadCable Assembly Rotator Head Chute Rotator Control Lever ScrewsNUT Washer Speed Control AssemblyRetainer Springs PINSnow Thrower Section Power Steering and Wheels Repair Power Steering Clutch Cable Spring PIN Bellcrank Link RetainerSnow Thrower Section Chassis / Engine / Pulleys Idler Pulley Belt Cover Right ScrewRight Bolt Left Bolt Drive Plate Slot Idler Spring Left Wheel Traction Belt Spring Auger Belt SpringFrame Slot For Drive Plate Drive Spring Barrel Connector Wood SupportHousing Screw Belt Guide Drive BeltSnow Thrower Section Drive Screws Flange Bearing HEX Head ScrewsNUT HEX Shaft Flange Bearing Pinion Gear Long HEX ShaftFrame Slot Drive Plate Assembly ScrewsNuts Instruction Lubricate HEX Shaft Axle Bearing ScrewsTo Reinstall Cable Assembly LocknutSnow Thrower Section Auger Housing / Impeller Assembly Replace Auger Shear Bolts Replace Impeller Shear Bolts Impeller Shear Bolts Auger Shear BoltsFor Husqvarna Parts Call 606-678-9623 or Impeller ShaftTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no Tecumseh 4-CYCLE Engine NO. no DescriptionService Notes Part Number 184962 printed for MY