Electrolux OHV service manual Install Auger Control ROD See Figs

Page 9

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

CONSUMER ASSEMBLY / PRE-OPERATION

TRACTION DRIVE	RETAINER
CONTROL LEVER	SPRING

TRACTION

DRIVE CON-

TROL ROD

DRIVE

CONTROL

BRACKET

FIG. 4

INSTALL AUGER CONTROL ROD (See Figs. 5 and 6)

The auger control rod has the short loop on the end of the spring as shown.

1.Slide rubber sleeve up rod and hook end of spring into control arm with loop opening up as shown.

2.Remove retainer spring from top end of rod.

3.With top end of rod positioned under right side of control panel, push down on rod and insert end of rod into hole in auger control bracket. Secure with retainer spring.

INSTALL DISCHARGE CHUTE / CHUTE ROTATER HEAD

AUGER CON-

TROL ROD

RUBBER

SLEEVE

CONTROL

ARM

LOOP

OPENING

UP

FIG. 5

AUGER
CONTROL	RETAINER	AUGER
ROD	RETAINER	AUGER
	SPRING	CONTROL
		LEVER

AUGER

CONTROL

BRACKET

FIG. 6

(See Fig. 7)

NOTE: The multi-wrench provided in your parts bag may be used to install the chute rotater head.

1.Place discharge chute assembly on top of chute base with discharge opening toward front of snow thrower.

2.Position chute rotater head over chute bracket. If nec- essary, rotate chute assembly to align square and pin on underside of chute rotater head with holes in chute bracket.

3.With chute rotater head and chute bracket aligned, position chute rotater head on pin and threaded stud of mounting bracket.

4.Install 3/8 washer and locknut on threaded stud and tighten securely.

CHUTE RO-

TATER HEAD

3/8 LOCKNUT

3/8 WASHER

CHUTE

BRACKET

PIN

THREADED

STUD

ROTATER HEAD

MOUNTING

BRACKET

FIG. 7

9

www.mymowerparts.com

Image 9

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training PreparationOperation Maintenance and StorageSpecifications Consumer Assembly Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Consumer Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleSee Fig Install Auger Control ROD See FigsInstall Chute Deflector Remote Control See Figs Install Weight BAG See FigCheck Tire Pressure Know Your Snow Thrower Consumer OperationRecoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Adjust Skid Plates See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineADD Gasoline See Fig To Start EngineSnow Throwing Tips Before StoppingIf Recoil Starter has Frozen General Recommendations Consumer MaintenanceBefore Each USE LubricationEngine CleaningConsumer Service and Adjustments To Adjust Snow Thrower HeightChute Deflector To Remove Wheels See Fig Carburetor OtherEngine OIL CylinderTroubleshooting 16 to 1/8 Belt GuideClearance Auger Belt Traction Belt Idler SpringProtective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control Rod2nd Reverse Position Speed Control Assembly AdjustmentNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Traction Auger Engagement Lever Screws Interlock Spring Check Wear HereConsole Lock TAB Into Hole Backside View Section Cable Assembly Rotator Head Spring Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsRetainer Springs Speed Control AssemblyNUT Washer PINSnow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering ClutchSnow Thrower Section Chassis / Engine / Pulleys Belt Cover Right Screw Right Bolt Left BoltIdler Pulley Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left WheelHousing Screw Barrel Connector Wood SupportFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive NUT HEX Shaft HEX Head ScrewsScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftDrive Plate Assembly Screws NutsFrame Slot Lubricate HEX Shaft Axle Bearing Screws InstructionCable Assembly Locknut To ReinstallSnow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear BoltsImpeller Shaft For Husqvarna Parts Call 606-678-9623 orTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE EngineService Notes Part Number 184962 printed for MY