Electrolux OHV Consumer Maintenance, General Recommendations, Before Each USE, Lubrication

Page 17

For Husqvarna Parts Call 606-678-9623 or 606-561-4983

CONSUMER MAINTENANCE

GENERAL RECOMMENDATIONS

LUBRICATION CHART

The warranty on this snow thrower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain snow thrower as instructed in this manual. Some adjust- ments will need to be made periodically to properly maintain your snow thrower.

All adjustments in the Service and Adjustments section of this manual should be checked at least once each season.

•Once a year, you should replace the spark plug and check belts for wear. A new spark plug will help your engine run better and last longer.

•Follow the maintenance schedule in this manual.

NOTE: Use only Original Equipment Manufacturer (OEM) parts to service this unit. Failure to do so can cause the unit to malfunction and pose a risk of injury to the operator.

BEFORE EACH USE

1.Check engine oil level.

2.Check for loose fasteners.

3.Check controls to be sure they are functioning prop- erly.

LUBRICATION

Keep your snow thrower well lubricated (See “LUBRI- CATION CHART”).

SAE 5W-30 Motor Oil

 See “ENGINE” in Maintenance section

 General

Purpose Grease

 Engine oil

 Auger grease fittings

Pivot points

SNOW THROWER

Always observe the safety rules when performing any maintenance.

TIRES

•Maintain proper air pressure in both tires (See “PROD- UCT SPECIFICATIONS” section in this manual).

17

•Keep tires free of gasoline and oil, which can harm rubber.

NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion.

www.mymowerparts.com

Image 17

Contents For Husqvarna Parts Call 606-678-9623 or To the technician using this manual Table of Contents Training PreparationOperation Maintenance and StorageSpecifications Consumer Assembly Parts Packed Separately in Carton HOW to SET UP Your Snow Thrower Consumer Assembly / PRE-OPERATIONRemove Snow Thrower from Carton Unfold Upper HandleSee Fig Install Auger Control ROD See FigsCheck Tire Pressure Install Chute Deflector Remote Control See FigsInstall Weight BAG See Fig Know Your Snow Thrower Consumer OperationRecoil auxiliary starter handle used for starting the en Meets A.N.S.I. Safety RequirementsStopping HOW to USE Your Snow ThrowerTo Adjust Skid Plates See Fig Power Steering Operation See FigTo Throw Snow See Fig To Move Forward and Backward See FigCheck Engine OIL Level See Fig Before Starting the EngineADD Gasoline See Fig To Start EngineIf Recoil Starter has Frozen Snow Throwing TipsBefore Stopping General Recommendations Consumer MaintenanceBefore Each USE LubricationEngine CleaningChute Deflector Consumer Service and AdjustmentsTo Adjust Snow Thrower Height To Remove Wheels See Fig Carburetor OtherEngine OIL CylinderTroubleshooting 16 to 1/8 Belt GuideClearance Auger Belt Traction Belt Idler SpringProtective Sleeve JAM NUT Control ROD Feeler Gauge Adjustment for Drive System Control Rod2nd Reverse Position Speed Control Assembly AdjustmentNUT and Bolt Bellcrank Shifter Retainer Spring Control ROD LeverFeeler Gauge Retainer Ring Systems and Repair Procedures Snow Thrower Section Handles Console Lock TAB Into Hole Backside View Traction Auger Engagement Lever ScrewsInterlock Spring Check Wear Here Section Cable Assembly Rotator Head Spring Cable Assembly Rotator HeadDeflector Cable Assembly Chute Rotator Control Lever ScrewsRetainer Springs Speed Control AssemblyNUT Washer PINSnow Thrower Section Power Steering and Wheels Cable Spring PIN Bellcrank Link Retainer Repair Power Steering ClutchSnow Thrower Section Chassis / Engine / Pulleys Idler Pulley Belt Cover Right ScrewRight Bolt Left Bolt Traction Belt Spring Auger Belt Spring Drive Plate Slot Idler Spring Left WheelHousing Screw Barrel Connector Wood SupportFrame Slot For Drive Plate Drive Spring Belt Guide Drive BeltSnow Thrower Section Drive NUT HEX Shaft HEX Head ScrewsScrews Flange Bearing Flange Bearing Pinion Gear Long HEX ShaftFrame Slot Drive Plate Assembly ScrewsNuts Lubricate HEX Shaft Axle Bearing Screws InstructionCable Assembly Locknut To ReinstallSnow Thrower Section Auger Housing / Impeller Assembly Impeller Shear Bolts Auger Shear Bolts Replace Auger Shear Bolts Replace Impeller Shear BoltsImpeller Shaft For Husqvarna Parts Call 606-678-9623 orTecumseh 4-CYCLE OHV Engine KEY Part NO. no Description KEY KEY Part Description NO. no NO. no Description Tecumseh 4-CYCLE EngineService Notes Part Number 184962 printed for MY