Able Planet OL-1747-02 manual Devfunc Anate Msgwlmp Specl

Page 19

Chapter 1 Siemens 9751 9006i DTMF Integration

Programming the Phone System

Table 1-3 ADDSCSU Parameter Settings for MWI Ports

Parameter	Required Setting

HTLNIDX	(leave field blank)

DEVFUNC	ANATE

MSGWLMP	N

SPECL	(leave field blank)

DIAL	DTMF

DLIDX	(leave field blank)

INS	Y

SPDC1	(leave field blank)

SPDC2	(leave field blank)

SPDI	(leave field blank)

LCROSD1	(leave field blank)

LCROSD2	(leave field blank)

LCRCOSV1	(leave field blank)

LCRCOSV2	(leave field blank)

FAXSERV	(leave field blank)

DTS	N

AVD	N

CDIDX	(leave field blank)

All MWIs on subscriber extensions are turned off when the phone system restarts. To reset MWIs, run the phone system Message-Waiting Refresh utility on menu 13.5.

If you use the broken dial tone for MWIs, subscribers can confuse the MWIs with the stutter dial tone that the phone system uses for another purpose.

Step 5 Repeat Step 4 for each remaining SLMA voice messaging port that sets MWIs.

Step 6 Use the ADDHUNT command to create a hunt group for the answering voice messaging ports. All subscriber phones will use this hunt group to reach Cisco Unity. The hunt group must have the following parameters while the remaining parameters keep their default values.

		Siemens 9751 9006i DTMF Integration Guide
		Siemens 9751 9006i DTMF Integration Guide
	OL-1747-02			1-7
	OL-1747-02			1-7

Image 19

Contents Siemens 9751 9006i Dtmf Integration Guide Siemens 9751 9006i Dtmf Integration Guide Preface Exiting the Cisco Unity Software A-1 Audience PurposeConventions OrganizationConvention Description Document Location Cisco Unity DocumentationViii Ordering Documentation Obtaining DocumentationWorld Wide Web Documentation CD-ROMDocumentation Feedback Obtaining Technical AssistanceCisco.com Technical Assistance Center Contacting TAC by Using the Cisco TAC WebsiteContacting TAC by Telephone Integration Steps Integration OverviewPhone System RequirementsCisco Unity Server Integration DescriptionProgramming the Phone System Integration FeaturesTo program the phone system for analog ports Parameter Required SettingNytpe NAT Actcde Devfunc Anate Msgwlmp Specl Type VCE FPN ParameterTo confirm that the integration is enabled Configuring Cisco Unity for the IntegrationTransfer Type Usage To enter port settings Switch Parameter Required SettingTo set up the test configuration Testing the IntegrationTo test an external call with release transfer To test an internal call with release transfer To test supervised transfer To set up supervised transfer on Cisco UnityTo return Example Subscriber to the default settings Dual Phone System Integration Overview Integration Steps When No Phone Systems Are InstalledSiemens 9751 9006i Dtmf Integration Guide Changing Cisco Unity Administrator Settings To specify switch settings for the traditional phone system To modify voice port settings To specify switch settings for Cisco CallManagerSiemens 9751 9006i Dtmf Integration Guide OL-1747-02 Changing the Number of Installed Ports To remove the existing AV-Cisco TSP To reinstall the AV-Cisco service providerOL-1747-02 To exit the Cisco Unity software from another computer Exiting the Cisco Unity SoftwareTo shut down or restart the Cisco Unity server Starting the Cisco Unity SoftwareClick Start Cisco Unity To start the Cisco Unity software from another computer Setting Up Cisco Unity to Remap Extension Numbers Remapping Extension Numbers Remapping FeatureTo remap extension numbers Wildcard Result Syntax and ExamplesRule Original Number New Number Phone System Integration Click OK To set the Port assignments in the RegistryOL-1747-02 OL-1747-02