Sanyo HF15000L owner manual Safety Instructions

Page 5

Safety Instructions

All the safety and operating instructions should be read before the product is operated.

Read all of the instructions given here and retain them for later use. Unplug this projector from AC power supply before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

Follow all warnings and instructions marked on the projector.

For added protection to the projector during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet. This will prevent damage due to lightning and power line surges.

Do not expose this unit to rain or use near water... for

example, in a wet basement, near a swimming pool, etc...

Do not use attachments not recommended by the manufacturer as they may cause hazards.

Do not place this projector on an unstable cart, stand, or table. The projector may fall, causing serious injury to a child or adult, and serious damage to the projector. Use only with a cart or stand recommended by the manufacturer, or sold with the projector. Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturers.

An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

Slots and openings in the back and bottom of the cabinet are provided for ventilation, to ensure reliable operation of the equipment and to protect it from overheating.

The openings should never be covered with cloth or other materials, and the bottom opening should not be blocked by placing the projector on a bed, sofa, rug, or other similar surface. This projector should never be placed near or over a radiator or heat register.

This projector should not be placed in a built-in installation such as a book case unless proper ventilation is provided.

Never push objects of any kind into this projector through cabinet slots as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. Never spill liquid of any kind on the projector.

Do not install the projector near the ventilation duct of air- conditioning equipment.

This projector should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied, consult your authorized dealer or local power company.

Do not overload wall outlets and extension cords as this can result in fire or electric shock. Do not allow anything to rest on the power cord. Do not locate this projector where the cord may be damaged by persons walking on it.

Do not attempt to service this projector yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

Unplug this projector from wall outlet and refer servicing to qualified service personnel under the following conditions:

a.When the power cord or plug is damaged or frayed.

b.If liquid has been spilled into the projector.

c.If the projector has been exposed to rain or water.

d.If the projector does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the projector to normal operation.

e.If the projector has been dropped or the cabinet has been damaged.

f.When the projector exhibits a distinct change in performance-this indicates a need for service.

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or injury to persons.

Upon completion of any service or repairs to this projector, ask the service technician to perform routine safety checks to determine that the projector is in safe operating condition.

NOTE FOR CUSTOMERS IN THE US

Hg LAMP(S) inside this product contain mercury and must be recycled or disposed of according to local, state or federal laws.

Image 5
Contents Model PLC-HF15000L Functionally Rich Motor-driven Lens Shift Features and DesignTable of Contents To The Owner Safety PrecautionSafety Instructions Air Circulation Safety InstructionsUpward projection, do Installing the Projector in Proper DirectionsNot tilt the projector over Degrees right and leftTransporting the Projector Moving the ProjectorCanadian Radio Interference Regulations ComplianceFederal Communications Commission Notice Part Names and Functions 4Adjustable Feet 5Air Intake VentFront Back BottomPart Names and Functions Terminals and ConnectorsSide Control Side Control and IndicatorsLamp 1/2/3/4 Replace indicators IndicatorsTimer button Signal Emission indicator9IMAGE Adjust button STAND-BY buttonWired Remote Control Remote Control Battery InstallationRemote Control Receivers and Operating Range Remote Control Codes Lens Installation InstallationPicture Level and Pitch Adjustment Positioning ProjectorLens Shift Adjustment InstallationTerminals of Projector Replacement of TerminalCables used for connection Connecting to ComputerProfessional Digital VCR Connecting to Video EquipmentTo loosen the cable tie Attaching the Cable TiePower cord clamp Connecting the AC Power CordProjector side For the U.KTurning On the Projector Basic OperationTurning Off the Projector What is PIN code?Basic Operation Basic Operation How to Operate the On-Screen Menu Basic Operation Main Menu Basic Operation Operating with Projector Control Basic Operation Operating with Remote Control INFO. button Light button Timer buttonFreeze button Filter buttonStandard Basic Operation Keystone CorrectionCorner correction Press the Point 8 buttonInput Selection Remote Control OperationDirect Operation Side ControlMenu Operation Input Selection Computer Input Source SelectionRGBScart Input Selection Video Input Source SelectionRgbpc digital VideoComputer System Selection Computer InputAutomatic Multi-Scan System Selecting Computer System ManuallyMenu. Use the Point ed buttons to select PC adjust Computer Input Auto PC AdjustmentTo store the adjusted parameters Direct OperationComputer Input Manual PC Adjustment Mode free ResetComputer Input StoreReal Image select StandardDynamic ImageImage Adjust Menu Computer Input Image AdjustmentContrast BrightnessWhite balance Red Color tempWhite balance Green White balance BlueAuto picture control Offset Red/Green/BlueAdvanced color SharpnessComputer Input Screen Size Adjustment Digital zoom Custom adjDigital zoom + Corner correction KeystoneCorner pattern CeilingVideo System Selection Video InputVideo Input Picture level adjusted with fine toneUse the Point ed buttons to select Image select Image select menu StandardTint Video Input Image AdjustmentColor Offset Red/Green/Blue Confirmation box appears and then select Yes Noise reductionProgressive Natural wide Screen Size AdjustmentFlexible aspect ratio Choose a Corner pattern mode among Red, White, Blue, and OffSettings SettingsBackground Lamp modeProjects a blue background Projects a captured imagePicture in Picture Lamp life controlLamp interval Set the Frame Lock to Main picture or Sub picture Display position setting screenColor matching Edge blendingAdvanced color matching Advanced color matching Measured information Test patternLogo Logo and Logo PIN code lock settings Hdmi setupLogo select CaptureLogo PIN code lock Change the Logo PIN code lock settingChange Logo PIN code To enter a Logo PIN code lock To change the Logo PIN codeTo change the code for the remote control Select a remote control code in this Setting MenuFilter control Fan controlTimer left before Lamp is off Power managementRC sensor Direct onPIN code lock Security Key lock and PIN code lockKey lock To enter a PIN code To change the PIN code lock settingTo change PIN code To change the PIN codeShutter Projector IDClosed caption Video delay controlAppear at turning on and selecting input source Filter counterFactory default TimerHow to Overlap the Projection Images on a Screen How To Overlap the Projection ImagesColor matching How to Overlap the Projection ImagesMaintaining the AMC unit Maintenance and CareReplacing the Filters Maintenance and CareMaintenance and Care Resetting the Filter Counter Lamp Management Lamp Replacement Lamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below IndicatorsAppendix TroubleshootingAppears on the screen AppendixShutter does not Computer Input Menu TreeComputer Input/HDMI Input/Video Input Video Input Hdmi Input/Video InputSetting Indicators Indicators and Projector ConditionTemperature inside the projector is abnormally Temperature inside the projector is elevatedTemperature returns to normal, the Power Indicator lights green and the projector can beSetting, the icon as shown in appears on If the Filter counter reached a time set in the timerScreen and the Warning Filter indicator on Timer setting, the icon shown in appears onDisplay Compatible Computer SpecificationsSvga BNC, S Board POA-AMD25VD3 Supported Signal Format for Optional BoardDual Link SDI Board POA-AMD22SDIDL Technical Specifications PJ Link Notice Optional PartsControl Port Connector D-sub 9 pin Configurations of TerminalsAnalog TERMINALMini D-sub 15 pin USB PORTSeries B Hdmi TERMINAL19 pin Type aLogo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Unit mm inch DimensionsList of Picture in Picture Format Serial Control InterfaceExample Status Read Commands KL8A