Sanyo HF15000L Input Selection, Direct Operation, Side Control, Remote Control Operation

Page 33

Input Selection

Direct Operation

Side Control

INPUT button

The input source changes each time you press the INPUT button on the side control as follows: Input 1→Input 2→ ...

Before using the INPUT button on the side control or the remote control, you must select a correct input source by On-Screen Menu and the latest input source will be displayed.

Remote Control Operation

Press the INPUT 1, INPUT 2, INPUT 3 or INPUT 4 button on the remote control. The input source appears on the screen as you press each button. Select the connected input source.

INPUT 1 button

Input 1

RGB (PC analog)

RGB (Scart)

RGB(PC digital)

RGB(AV HDCP)

HDMI

INPUT 2 button

Input 2

RGB

Y,Pb/Cb,Pr/Cr

Video

S-video

Remote Control

INPUT 1/2/3/4

buttons

✔Note:

•“Input 3” and/or “Input 4” are selectable only when interface board(s) are connected to either or both of the slots.

Image 33

Contents Model PLC-HF15000L Functionally Rich Motor-driven Lens Shift Features and DesignTable of Contents To The Owner Safety PrecautionSafety Instructions Air Circulation Safety InstructionsUpward projection, do Installing the Projector in Proper DirectionsNot tilt the projector over Degrees right and leftTransporting the Projector Moving the ProjectorCompliance Federal Communications Commission NoticeCanadian Radio Interference Regulations Part Names and Functions 4Adjustable Feet 5Air Intake VentFront Back BottomPart Names and Functions Terminals and ConnectorsSide Control Side Control and IndicatorsLamp 1/2/3/4 Replace indicators IndicatorsTimer button Signal Emission indicator9IMAGE Adjust button STAND-BY buttonRemote Control Battery Installation Remote Control Receivers and Operating RangeWired Remote Control Remote Control Codes Lens Installation InstallationPicture Level and Pitch Adjustment Positioning ProjectorLens Shift Adjustment InstallationTerminals of Projector Replacement of TerminalCables used for connection Connecting to ComputerProfessional Digital VCR Connecting to Video EquipmentTo loosen the cable tie Attaching the Cable TiePower cord clamp Connecting the AC Power CordProjector side For the U.KTurning On the Projector Basic OperationWhat is PIN code? Basic OperationTurning Off the Projector Basic Operation How to Operate the On-Screen Menu Basic Operation Main Menu Basic Operation Operating with Projector Control Basic Operation Operating with Remote Control INFO. button Light button Timer buttonFreeze button Filter buttonStandard Basic Operation Keystone CorrectionCorner correction Press the Point 8 buttonInput Selection Remote Control OperationDirect Operation Side ControlMenu Operation Input Selection Computer Input Source SelectionRGBScart Input Selection Video Input Source SelectionRgbpc digital VideoComputer System Selection Computer InputAutomatic Multi-Scan System Selecting Computer System ManuallyMenu. Use the Point ed buttons to select PC adjust Computer Input Auto PC AdjustmentTo store the adjusted parameters Direct OperationComputer Input Manual PC Adjustment Mode free ResetComputer Input StoreReal Image select StandardDynamic ImageImage Adjust Menu Computer Input Image AdjustmentContrast BrightnessWhite balance Red Color tempWhite balance Green White balance BlueAuto picture control Offset Red/Green/BlueAdvanced color SharpnessComputer Input Screen Size Adjustment Custom adj Digital zoom +Digital zoom Corner correction KeystoneCorner pattern CeilingVideo System Selection Video InputVideo Input Picture level adjusted with fine toneUse the Point ed buttons to select Image select Image select menu StandardVideo Input Image Adjustment ColorTint Offset Red/Green/Blue Noise reduction ProgressiveConfirmation box appears and then select Yes Natural wide Screen Size AdjustmentFlexible aspect ratio Choose a Corner pattern mode among Red, White, Blue, and OffSettings SettingsBackground Lamp modeProjects a blue background Projects a captured imageLamp life control Lamp intervalPicture in Picture Set the Frame Lock to Main picture or Sub picture Display position setting screenColor matching Edge blendingAdvanced color matching Advanced color matching Measured information Test patternLogo Logo and Logo PIN code lock settings Hdmi setupLogo select CaptureLogo PIN code lock Change the Logo PIN code lock settingChange Logo PIN code To enter a Logo PIN code lock To change the Logo PIN codeTo change the code for the remote control Select a remote control code in this Setting MenuFilter control Fan controlTimer left before Lamp is off Power managementRC sensor Direct onSecurity Key lock and PIN code lock Key lockPIN code lock To enter a PIN code To change the PIN code lock settingTo change PIN code To change the PIN codeShutter Projector IDClosed caption Video delay controlAppear at turning on and selecting input source Filter counterFactory default TimerHow to Overlap the Projection Images on a Screen How To Overlap the Projection ImagesColor matching How to Overlap the Projection ImagesMaintaining the AMC unit Maintenance and CareReplacing the Filters Maintenance and CareMaintenance and Care Resetting the Filter Counter Lamp Management Lamp Replacement Lamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below IndicatorsAppendix TroubleshootingAppears on the screen AppendixShutter does not Menu Tree Computer Input/HDMI Input/Video InputComputer Input Video Input Hdmi Input/Video InputSetting Indicators Indicators and Projector ConditionTemperature inside the projector is abnormally Temperature inside the projector is elevatedTemperature returns to normal, the Power Indicator lights green and the projector can beSetting, the icon as shown in appears on If the Filter counter reached a time set in the timerScreen and the Warning Filter indicator on Timer setting, the icon shown in appears onDisplay Compatible Computer SpecificationsSvga Supported Signal Format for Optional Board Dual Link SDI Board POA-AMD22SDIDLBNC, S Board POA-AMD25VD3 Technical Specifications PJ Link Notice Optional PartsControl Port Connector D-sub 9 pin Configurations of TerminalsAnalog TERMINALMini D-sub 15 pin USB PORTSeries B Hdmi TERMINAL19 pin Type aPIN Code Number Memo PIN Code Lock NoLogo PIN Code Lock No Unit mm inch DimensionsList of Picture in Picture Serial Control Interface ExampleFormat Status Read Commands KL8A