Sanyo HF15000L owner manual Lamp Handling Precautions

Page 77

Maintenance and Care

ORDER REPLACEMENT LAMP

Replacement Lamp can be ordered through your dealer. When ordering a Projection Lamp, give the following information to the dealer.

Model No. of your projector:

PLC-HF15000L

Replacement Lamp Type No.:

POA-LMP147

 

 

(Service Parts No. 610 350 9051)

LAMP HANDLING PRECAUTIONS

This projector uses high-pressure lamps which must be handled carefully and properly.

Improper handling may result in accidents, injury, or create a fire hazard.

Lamp lifetime may differ from lamp to lamp and according to the environment of use. There is no guarantee of the same lifetime for each lamp. Some lamps may fail or terminate their lifetime in a shorter period of time than other similar lamps.

If the projector indicates that the lamp should be replaced, i.e., if the LAMP REPLACE indicator lights up, replace the lamp with a new one after the lamps have cooled down. (Follow carefully the instructions in the Lamp Replacement section of this manual.) Continuous use of the lamp with the LAMP REPLACE indicator lighted may increase the risk of lamp explosion.

Lamp may explode as a result of vibration, shock or degradation as a result of hours of use as its lifetime draws to an end. Risk of explosion may differ according to the environment or conditions in which the projector and lamp are being used.

IF A LAMP EXPLODES,THE FOLLOWING SAFETY PRECAUTIONS SHOULD BE TAKEN.

If a lamp explodes, disconnect the projector’s AC plug from the AC outlet immediately. Contact an authorized service center for a checkup of the unit and replacement of the lamp. Additionally, check carefully to ensure that there are no broken shards or pieces of glass around the projector or coming out from the cooling air circulation holes. Any broken shards found should be cleaned up carefully. No one should check the inside of the projector except those who are authorized trained technicians and who are familiar with projector service. Inappropriate attempts to service the unit by anyone, especially those who are not appropriately trained to do so, may result in an accident or injury caused by pieces of broken glass.

77

Image 77
Contents Model PLC-HF15000L Functionally Rich Motor-driven Lens Shift Features and DesignTable of Contents To The Owner Safety PrecautionSafety Instructions Air Circulation Safety InstructionsUpward projection, do Installing the Projector in Proper DirectionsNot tilt the projector over Degrees right and leftTransporting the Projector Moving the ProjectorCanadian Radio Interference Regulations ComplianceFederal Communications Commission Notice Part Names and Functions 4Adjustable Feet 5Air Intake VentFront Back BottomPart Names and Functions Terminals and ConnectorsSide Control Side Control and IndicatorsLamp 1/2/3/4 Replace indicators IndicatorsTimer button Signal Emission indicator9IMAGE Adjust button STAND-BY buttonWired Remote Control Remote Control Battery InstallationRemote Control Receivers and Operating Range Remote Control Codes Lens Installation InstallationPicture Level and Pitch Adjustment Positioning ProjectorLens Shift Adjustment InstallationTerminals of Projector Replacement of TerminalCables used for connection Connecting to ComputerProfessional Digital VCR Connecting to Video EquipmentTo loosen the cable tie Attaching the Cable TiePower cord clamp Connecting the AC Power CordProjector side For the U.KTurning On the Projector Basic OperationTurning Off the Projector What is PIN code?Basic Operation Basic Operation How to Operate the On-Screen Menu Basic Operation Main Menu Basic Operation Operating with Projector Control Basic Operation Operating with Remote Control INFO. button Light button Timer buttonFreeze button Filter buttonStandard Basic Operation Keystone CorrectionCorner correction Press the Point 8 buttonInput Selection Remote Control OperationDirect Operation Side ControlMenu Operation Input Selection Computer Input Source SelectionRGBScart Input Selection Video Input Source SelectionRgbpc digital VideoComputer System Selection Computer InputAutomatic Multi-Scan System Selecting Computer System ManuallyMenu. Use the Point ed buttons to select PC adjust Computer Input Auto PC AdjustmentTo store the adjusted parameters Direct OperationComputer Input Manual PC Adjustment Mode free ResetComputer Input StoreReal Image select StandardDynamic ImageImage Adjust Menu Computer Input Image AdjustmentContrast BrightnessWhite balance Red Color tempWhite balance Green White balance BlueAuto picture control Offset Red/Green/BlueAdvanced color SharpnessComputer Input Screen Size Adjustment Digital zoom Custom adjDigital zoom + Corner correction KeystoneCorner pattern CeilingVideo System Selection Video InputVideo Input Picture level adjusted with fine toneUse the Point ed buttons to select Image select Image select menu StandardTint Video Input Image AdjustmentColor Offset Red/Green/Blue Confirmation box appears and then select Yes Noise reductionProgressive Natural wide Screen Size AdjustmentFlexible aspect ratio Choose a Corner pattern mode among Red, White, Blue, and OffSettings SettingsBackground Lamp modeProjects a blue background Projects a captured imagePicture in Picture Lamp life controlLamp interval Set the Frame Lock to Main picture or Sub picture Display position setting screenColor matching Edge blendingAdvanced color matching Advanced color matching Measured information Test patternLogo Logo and Logo PIN code lock settings Hdmi setupLogo select CaptureLogo PIN code lock Change the Logo PIN code lock settingChange Logo PIN code To enter a Logo PIN code lock To change the Logo PIN codeTo change the code for the remote control Select a remote control code in this Setting MenuFilter control Fan controlTimer left before Lamp is off Power managementRC sensor Direct onPIN code lock Security Key lock and PIN code lockKey lock To enter a PIN code To change the PIN code lock settingTo change PIN code To change the PIN codeShutter Projector IDClosed caption Video delay controlAppear at turning on and selecting input source Filter counterFactory default TimerHow to Overlap the Projection Images on a Screen How To Overlap the Projection ImagesColor matching How to Overlap the Projection ImagesMaintaining the AMC unit Maintenance and CareReplacing the Filters Maintenance and CareMaintenance and Care Resetting the Filter Counter Lamp Management Lamp Replacement Lamp Handling Precautions Cleaning the Projector Cabinet Cleaning the Projection LensThen check the matters below IndicatorsAppendix TroubleshootingAppears on the screen AppendixShutter does not Computer Input Menu TreeComputer Input/HDMI Input/Video Input Video Input Hdmi Input/Video InputSetting Indicators Indicators and Projector ConditionTemperature inside the projector is abnormally Temperature inside the projector is elevatedTemperature returns to normal, the Power Indicator lights green and the projector can beSetting, the icon as shown in appears on If the Filter counter reached a time set in the timerScreen and the Warning Filter indicator on Timer setting, the icon shown in appears onDisplay Compatible Computer SpecificationsSvga BNC, S Board POA-AMD25VD3 Supported Signal Format for Optional BoardDual Link SDI Board POA-AMD22SDIDL Technical Specifications PJ Link Notice Optional PartsControl Port Connector D-sub 9 pin Configurations of TerminalsAnalog TERMINALMini D-sub 15 pin USB PORTSeries B Hdmi TERMINAL19 pin Type aLogo PIN Code Lock No PIN Code Number MemoPIN Code Lock No Unit mm inch DimensionsList of Picture in Picture Format Serial Control InterfaceExample Status Read Commands KL8A