Turning off the power

Page 20

Power on/off

1. Press the STANDBY/ON button on the projector or the remote control.

The message "Power off?" will appear on the screen for approximately 5 seconds.

2. Press the STANDBY/ON button on the projector or the remote control again while the message appears.

The projector lamp will go off, and the POWER indicator will begin blinking in orange. Then the POWER indicator will stop blinking and light in steady orange when the lamp cooling is complete.

3. Make sure that the power indicator lights in steady orange, and set the power switch to the OFF position. The POWER indicator will go off. Do not set the power switch to the OFF position while the POWER indicator is green or blinking.

Power off?

POWER (Blinking in orange)

POWER (Steady orange)

4. Close the lens cover. For safety purposes, disconnect the power cord if the projector is not to be used for prolonged periods of time.

NOTE • Turn the power off in right order. First power off the connected devices and then the projector.

•Except for an emergency, whenever you turn the projector off, obey the procedure of the following “Turning off the power”, and do not disconnect the power cord until the procedure is completed. Neglect causes a damage of the electrode and un- lighting of the lamp.

•This projector is controlled by an internal microprocessor. Under certain exceptional circumstances, the projector may not operate correctly even for turning off the power. In such a case, please push the restart switch (6) by using a pin or similar. After making sure that the power indicator lights to solid orange, set the power switch to the OFF position. Only push the restart switch in these exceptional instances.

•When a power supply is shut off with a power failure or the restart switch, before turning on again, make the projector cool down at least 10 minutes without operating.

Contents Thank you for purchasing this projector Trademark acknowledgmentEDPJ32 User’s Manual - Operating GuideContent Power on/offBefore use PreparationsMultifunctional settings MaintenanceTroubleshooting Warranty and after-serviceAbout this manual Projector featuresBefore use About contents of package 47, 48 Part namesProjector Remote control Control buttonsPreparations Fastening the lens coverFilter cover’s knob Filter cover for bottom-up use with an air ﬁlter About the ﬁlter cover bottom-up useTabs When put on a table When suspended from the ceiling ArrangementFor 169 screens For 43 screensElevator button Adjusting the projector’s elevatorElevator feet Connecting your devices Examples of connection with a VCR/DVD playerExamples of connection with a computer Example of computer signal About Plug-and-Play capabilityConnecting power supply Loading batteries into the remote control Using the remote control Power on/off Turning on the powerTurning off the power Temporarily muting the sound Adjusting the volumeOperating POWER INPUT Selecting an input signalSearching an input signal For a 169 signal For a 43 signal For no signal 43  Selecting an aspect ratioAdjusting the zoom magnifying power Adjusting the focusUsing the automatic adjustment feature  For an RGB signalAdjusting the position Correcting the keystone distortionsUsing the partial magnify feature Freezing the screenTemporarily blanking the screen Multifunctional settings Using the menu function1. To display a menu 2. To choose the target menu3. To choose the target item 2 Advanced MENU → One of Advanced menus ex. SETUP menu3 Advanced MENU → EASY MENU 1 In the EASY MENU ex. KEYSTONE6. To reset 4. To operate5. To return to the previous menu 7. To close the menuEASY MENU EASY MENU continued Using a test pattern PICTURE menuTo adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM GAIN adjustments mainly affect color intensity on PICTURE menu continuedTo adjust CUSTOM Using the buttons / switches the progress mode IMAGE menu at the frame area of the picture. In such a case, please adjust small IMAGE menu continuedWhen this adjustment is too large, certain degradation may appear Choosing this item performs the automatic adjustment feature INPUT menu SETUP menu MIRROR item in the SETUP menu, if the projector screen is inclinedSCREEN menu the frame may not move for some signals. To restore the screen SCREEN menu continuedAlthough the adjustable range will vary depending on inputs, and MyScreen Lock MESSAGEblinking. Please refer to the section “Turning off the power”.  OPTION menuautomatically. When the time is set to 1 to 99, and when the passed OPTION menu continued press the ENTER button on the remote control or the INPUT button you to clean “REMINDER...” will appear after the timer reaches thecontinued 50h  100h  200h  300h  TURN OFFMaintenance LampIn the case of replacement by yourself Type number = DT007071 Press the MENU button to display a menu Air ﬁlter Type number = NJ22642Usual ﬁlter cover Filter cover for bottom-up useFilter cover for bottom-up use Caring for the lens Caring for the cabinet and remote controlInside of the projector Troubleshooting There is no input signalA note of precaution when cleaning the air ﬁlter Related messagesRegarding the indicator lamps The projector is cooling down. A certain errorThe projector is in a standby state The projector is in an on stateRegarding the indicator lamps continued Phenomena that may easily be taken as machine defects If the situation cannot be correctedPerform picture adjustments by changing the COLOR TEMP, COLOR Warranty and after-service SpeciﬁcationsDimension diagram 202 285Speciﬁcations 33.5