About the ﬁlter cover bottom-up use, Tabs

Page 9

Slowly turn the projector so that the bottom is facing up.

Preparations

About the ﬁlter cover bottom-up use

When the projector is installed bottom up, please use the accessory ﬁlter cover for bottom-up use. It is higher than usual ﬁlter cover, to keep the space for intake ventilation. Please change the ﬁlter cover in the following procedure.

ENGLISH

1. Disconnect all the connectors and adapters that were connected to the projector’s ports.

Then slowly turn the projector so that the lens-side is facing up. While the projector is placed lens-side up, hold the projector.

2. Remove the ﬁlter cover. Hold the knobs while pulling out it. If the projector was used before, please clean the air ﬁlter referring the section “Air ﬁlter”. (50)

Tabs

4. Set the ﬁlter cover for bottom- up use. Interlocking the tabs, snap the ﬁlter cover for bottom- up use into place.

Filter cover’s knob

Filter cover for bottom-up use (with an air ﬁlter)

WARNING ►Do not replace the ﬁlter cover and/or air ﬁlter during use or immediately after use. Handling while the projector is in a high temperature could cause a burn and/or malfunction to the projector.

►Do not use the projector with the air ﬁlter and the ﬁlter cover removed. Do not remove the ﬁlter cover and the air ﬁlter in a smoky or dusty place. It could result in a ﬁre and/or malfunction to the projector.

CAUTION ►Please be careful for the projector not to fall. While the projector is placed lens-side up, hold the projector.

Contents Trademark acknowledgment Thank you for purchasing this projectorEDPJ32 User’s Manual - Operating GuidePower on/off ContentBefore use PreparationsMaintenance Multifunctional settingsTroubleshooting Warranty and after-serviceProjector features Before useAbout this manual About contents of package Part names Projector47, 48 Control buttons Remote controlFastening the lens cover PreparationsAbout the ﬁlter cover bottom-up use TabsFilter cover’s knob Filter cover for bottom-up use with an air ﬁlter Arrangement When put on a table When suspended from the ceilingFor 43 screens For 169 screensAdjusting the projector’s elevator Elevator feetElevator button Examples of connection with a VCR/DVD player Connecting your devicesExamples of connection with a computer About Plug-and-Play capability Example of computer signalConnecting power supply Loading batteries into the remote control Using the remote control Turning on the power Power on/offTurning off the power Adjusting the volume OperatingTemporarily muting the sound Selecting an input signal Searching an input signalPOWER INPUT For a 43 signal For a 169 signal For no signal 43  Selecting an aspect ratioAdjusting the focus Adjusting the zoom magnifying powerUsing the automatic adjustment feature  For an RGB signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the partial magnify featureTemporarily blanking the screen Using the menu function Multifunctional settings1. To display a menu 2. To choose the target menu2 Advanced MENU → One of Advanced menus ex. SETUP menu 3. To choose the target item3 Advanced MENU → EASY MENU 1 In the EASY MENU ex. KEYSTONE4. To operate 6. To reset5. To return to the previous menu 7. To close the menuEASY MENU EASY MENU continued PICTURE menu To adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOMUsing a test pattern PICTURE menu continued To adjust CUSTOMGAIN adjustments mainly affect color intensity on Using the buttons / switches the progress mode IMAGE menu IMAGE menu continued When this adjustment is too large, certain degradation may appearat the frame area of the picture. In such a case, please adjust small Choosing this item performs the automatic adjustment feature INPUT menu MIRROR item in the SETUP menu, if the projector screen is inclined SETUP menuSCREEN menu SCREEN menu continued Although the adjustable range will vary depending on inputs, andthe frame may not move for some signals. To restore the screen MESSAGE MyScreen LockOPTION menu automatically. When the time is set to 1 to 99, and when the passedblinking. Please refer to the section “Turning off the power”.  OPTION menu continued you to clean “REMINDER...” will appear after the timer reaches the press the ENTER button on the remote control or the INPUT buttoncontinued 50h  100h  200h  300h  TURN OFFLamp MaintenanceType number = DT00707 In the case of replacement by yourself1 Press the MENU button to display a menu Type number = NJ22642 Air ﬁlterUsual ﬁlter cover Filter cover for bottom-up useFilter cover for bottom-up use Caring for the cabinet and remote control Inside of the projectorCaring for the lens There is no input signal TroubleshootingA note of precaution when cleaning the air ﬁlter Related messagesThe projector is cooling down. A certain error Regarding the indicator lampsThe projector is in a standby state The projector is in an on stateRegarding the indicator lamps continued If the situation cannot be corrected Phenomena that may easily be taken as machine defectsPerform picture adjustments by changing the COLOR TEMP, COLOR Speciﬁcations Warranty and after-service202 285 Dimension diagramSpeciﬁcations 33.5