Hitachi EDPJ32 user manual Troubleshooting, Related messages, There is no input signal

Page 53

Troubleshooting

Troubleshooting

Related messages

When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.

Although these messages will be automatically disappeared around several minutes, it will be reappeared every time the power is turned on.

Message

Description

 

 

NO INPUT IS DETECTED

There is no input signal.

Please confirm the signal input connection, and the status

ON ***

of the signal source.

 

 

The horizontal or vertical wavelength of the input signal

SYNC IS OUT OF RANGE

is out of the response parameter range of this unit.

ON *** fH *****kHz fV *****Hz

Please confirm the specs for your projector or the signal

 

source specs.

 

The internal portion temperature is rising.

 

Please turn the power OFF, and allow the unit to cool down

 

at least 20 minutes. After having confirmed the following

 

items, please turn the power ON again.

CHECK THE AIR FLOW

• Is there blockage of the air passage aperture?

• Is the air filter dirty?

 

 

• Does the peripheral temperature exceed 35°C?

 

• If the same indication is displayed after the remedy,

 

please set FAN SPEED of the SERVICE item in the

 

OPTION menu to HIGH. (45)

REMINDER

 

*** HRS PASSED AFTER THE LAST

A note of precaution when cleaning the air filter.

FILTER CHECK.

Please immediately turn the power off, and clean or change

FILTER MAINTENANCE IS ESSENTIAL

the air filter by referring to the “Air Filter” section of this

TO REMOVE WARNING MESSAGE,

manual. After you have cleaned or changed the air filter,

RESET FILTER TIMER.

please be sure to reset the filter timer. (45)

 

SEE MANUAL FURTHER INFO

 

 

 

ENGLISH

53

Page 52 Page 54
Image 53
Page 52 Page 54
Contents Trademark acknowledgment Thank you for purchasing this projectorEDPJ32 User’s Manual - Operating GuidePower on/off ContentBefore use PreparationsMaintenance Multifunctional settingsTroubleshooting Warranty and after-serviceAbout this manual Projector featuresBefore use About contents of package 47, 48 Part namesProjector Control buttons Remote controlFastening the lens cover PreparationsFilter cover’s knob Filter cover for bottom-up use with an air filter About the filter cover bottom-up useTabs Arrangement When put on a table When suspended from the ceilingFor 43 screens For 169 screensElevator button Adjusting the projector’s elevatorElevator feet Examples of connection with a VCR/DVD player Connecting your devicesExamples of connection with a computer About Plug-and-Play capability Example of computer signalConnecting power supply Loading batteries into the remote control Using the remote control Turning on the power Power on/offTurning off the power Temporarily muting the sound Adjusting the volumeOperating POWER INPUT Selecting an input signalSearching an input signal For a 43 signal For a 169 signal For no signal 43  Selecting an aspect ratioAdjusting the focus Adjusting the zoom magnifying powerUsing the automatic adjustment feature  For an RGB signalCorrecting the keystone distortions Adjusting the positionFreezing the screen Using the partial magnify featureTemporarily blanking the screen Using the menu function Multifunctional settings1. To display a menu 2. To choose the target menu2 Advanced MENU → One of Advanced menus ex. SETUP menu 3. To choose the target item3 Advanced MENU → EASY MENU 1 In the EASY MENU ex. KEYSTONE4. To operate 6. To reset5. To return to the previous menu 7. To close the menuEASY MENU EASY MENU continued Using a test pattern PICTURE menuTo adjust #1 CUSTOM, #2 CUSTOM or #3 CUSTOM GAIN adjustments mainly affect color intensity on PICTURE menu continuedTo adjust CUSTOM Using the buttons / switches the progress mode IMAGE menu at the frame area of the picture. In such a case, please adjust small IMAGE menu continuedWhen this adjustment is too large, certain degradation may appear Choosing this item performs the automatic adjustment feature INPUT menu MIRROR item in the SETUP menu, if the projector screen is inclined SETUP menuSCREEN menu the frame may not move for some signals. To restore the screen SCREEN menu continuedAlthough the adjustable range will vary depending on inputs, and MESSAGE MyScreen Lockblinking. Please refer to the section “Turning off the power”.  OPTION menuautomatically. When the time is set to 1 to 99, and when the passed OPTION menu continued you to clean “REMINDER...” will appear after the timer reaches the press the ENTER button on the remote control or the INPUT buttoncontinued 50h  100h  200h  300h  TURN OFFLamp MaintenanceType number = DT00707 In the case of replacement by yourself1 Press the MENU button to display a menu Type number = NJ22642 Air filterUsual filter cover Filter cover for bottom-up useFilter cover for bottom-up use Caring for the lens Caring for the cabinet and remote controlInside of the projector There is no input signal TroubleshootingA note of precaution when cleaning the air filter Related messagesThe projector is cooling down. A certain error Regarding the indicator lampsThe projector is in a standby state The projector is in an on stateRegarding the indicator lamps continued If the situation cannot be corrected Phenomena that may easily be taken as machine defectsPerform picture adjustments by changing the COLOR TEMP, COLOR Specifications Warranty and after-service202 285 Dimension diagramSpecifications 33.5
Top Page Image Contents